× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



It is both.

The first recommendation is is to create two vSCSI pairs between the host and client. One pair is used ONLY for tape and optical virtualization and the second pair for the initial set of disks. Use the RSTDDEVRSC(*ALL) Parm on this and all disk only vSCSI pairs.

Once you exceed the recommended maximum disk units per vSCSI pair then create additional pairs as needed for more virtual disks.

- Larry "DrFranken" Bolhuis

www.frankeni.com
www.iDevCloud.com
www.iInTheCloud.com

On 4/26/2014 9:49 PM, Steinmetz, Paul wrote:
Rob,

The best documentation I found is TR7 sg247858.pdf
7.4.1 Disk virtualization

I'm a bit confused by this statement.

More than one VSCSI pair can exist for the same client partition in this
environment. To minimize the performance impact on the host partition, the VSCSI
connection is used to send I/O requests, but not for the actual transfer of data. Using the
capability of the POWER Hypervisor for Logical Remote Direct Memory Access (LRDMA),
data is transferred directly from the physical adapter that is assigned to the host partition to a
buffer in memory of the client partition.

Further down

For performance reasons, you might consider creating multiple storage spaces that are
associated with multiple NWSDs. The rule of thumb is 6 - 8 storage spaces for each client
partition. This setup implies that you are also creating multiple sets of VSCSI adapter pairs
between the hosting partition and the client partition. Associate each hosting partition’s server
VSCSI adapter with a separate NWSD by referencing the VSCSI adapter’s resource name in
the NWSD, and then link storage spaces to the NWSDs. This action supplies multiple disk
arms for the client partition to use.

If I'm reading this correctly, its not the multiple NWSSTG that add the performance, but multiple NWSD

Is this correct?

Paul

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of rob@xxxxxxxxx
Sent: Saturday, April 26, 2014 7:59 PM
To: Midrange Systems Technical Discussion
Subject: RE: Distribute IBM i on available disk units Was: 70GB load source and 5 other drives

Each NWSD has an entry on the host configuration in the HMC. One server scsi entry for each client.

Now, I have this one machine that has a HUGE, busy, guest. That has 2 or
3 server scsi entries for that one guest and each server scsi entry has a client scsi entry. Why the multiples? Because there's a limit to the number of NWSSTG items per NSD.

WRKNWSD
Network
Server Text
MAIL1 MAIL1, Domino Guest lpar
MAIL1D1 MAIL1, More disk drives
MAIL1TO MAIL1, Tape and Optical

All three of these point to just one lpar.

WRKNWSSTG
MAIL1D101 MAIL1D1 1 *DYN *UPDATE
MAIL1D102 MAIL1D1 2 *DYN *UPDATE
MAIL1001 MAIL1 1 *DYN *UPDATE
MAIL1002 MAIL1 2 *DYN *UPDATE
MAIL1003 MAIL1 3 *DYN *UPDATE
MAIL1004 MAIL1 4 *DYN *UPDATE
MAIL1005 MAIL1 5 *DYN *UPDATE
MAIL1006 MAIL1 6 *DYN *UPDATE
MAIL1007 MAIL1 7 *DYN *UPDATE
MAIL1008 MAIL1 8 *DYN *UPDATE
MAIL1009 MAIL1 9 *DYN *UPDATE
MAIL1010 MAIL1 10 *DYN *UPDATE
MAIL1011 MAIL1 11 *DYN *UPDATE
MAIL1012 MAIL1 12 *DYN *UPDATE
MAIL1013 MAIL1 13 *DYN *UPDATE
MAIL1014 MAIL1 14 *DYN *UPDATE
MAIL1015 MAIL1 15 *DYN *UPDATE
MAIL1016 MAIL1 16 *DYN *UPDATE


Rob Berendt
--
IBM Certified System Administrator - IBM i 6.1 Group Dekko Dept 1600 Mail to: 2505 Dekko Drive
Garrett, IN 46738
Ship to: Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com





From: "Steinmetz, Paul" <PSteinmetz@xxxxxxxxxx>
To: "'Midrange Systems Technical Discussion'"
<midrange-l@xxxxxxxxxxxx>
Date: 04/26/2014 07:47 PM
Subject: RE: Distribute IBM i on available disk units Was: 70GB
load source and 5 other drives
Sent by: midrange-l-bounces@xxxxxxxxxxxx



Rob,

At this time, I'm only using the host and guest LPARs for creating and
testing DSLO images.
I'm the only user on these LPARS, so no performance issues.
I'm keeping it simple, 1 NWS.
However, things can change overnight, I want to have a good understanding
of the pros/cons with multiple NWS.
When you added additional NWS, did you also have to do any HMC config
changes?

Paul

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [
mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of rob@xxxxxxxxx
Sent: Saturday, April 26, 2014 7:29 PM
To: Midrange Systems Technical Discussion
Subject: RE: Distribute IBM i on available disk units Was: 70GB load
source and 5 other drives

Depends on the guest.
One has ~8 Domino servers. Each of these servers is clustered on to at
least two other servers.
One has only 1 Domino server and it sits in our DMZ as another cluster of
our DMZ Domino servers One has 1 Domino server and a full set of Infor's
software for testing.

Neither has a whale of a lot of active users.

We went with guesting so that with scattering each lpar gets 20 arms.
That, and if we add more we do not have to add more raid controllers.

This is the first time the biggest one is guested. It used to be the
host. Now we've gone to a dedicated host lpar.

The others used to have just one storage space and seemed rather slow.


Rob Berendt
--
IBM Certified System Administrator - IBM i 6.1 Group Dekko Dept 1600 Mail
to: 2505 Dekko Drive
Garrett, IN 46738
Ship to: Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com





From: "Steinmetz, Paul" <PSteinmetz@xxxxxxxxxx>
To: "'Midrange Systems Technical Discussion'"
<midrange-l@xxxxxxxxxxxx>
Date: 04/26/2014 07:14 PM
Subject: RE: Distribute IBM i on available disk units Was: 70GB
load source and 5 other drives
Sent by: midrange-l-bounces@xxxxxxxxxxxx



Rob,

I'm not sure if you previously stated, what is this guest LPAR used for?

Paul.

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [
mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of rob@xxxxxxxxx
Sent: Saturday, April 26, 2014 7:00 PM
To: Midrange Systems Technical Discussion
Subject: Re: Distribute IBM i on available disk units Was: 70GB load
source and 5 other drives

I'm digging what you're saying there. I'm no stranger to TRCASPBAL.


Rob Berendt
--
IBM Certified System Administrator - IBM i 6.1 Group Dekko Dept 1600 Mail
to: 2505 Dekko Drive
Garrett, IN 46738
Ship to: Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com





From: Sue Baker <sue.baker@xxxxxxxxxx>
To: midrange-l@xxxxxxxxxxxx
Date: 04/26/2014 02:46 PM
Subject: Re: Distribute IBM i on available disk units Was: 70GB
load source and 5 other drives
Sent by: midrange-l-bounces@xxxxxxxxxxxx



rob@xxxxxxxxx wrote on Sat, 26 Apr 2014 15:58:16 GMT:

At which point do you run:
STRASPBAL TYPE(*ENDALC)
of the load source?

1: After Task 8: Restore the operating system, beginning
with ƒ oTask 1: Starting to restore the
operating systemƒ ?

2: In the middle of the task 8 above? If so, at which step?

When?


If i is hosting i, I thing I would elect to attempt to run with
no drives in *ENCALC status until I actually see some sort of a
performance issue where high I/Os to the load source can be
clearly identified as the culprit.

At that time, I would run STRASPBAL *ENDALC for UNIT(1) followed
by a STRASPBAL *MOVDTA.

Other options could be to run a TRCASPBAL followed by a
STRASPBAL *USAGE to rearrange "cold" data. This would be in the
hope the hot load source becomes warm.


As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.