Re: Experince with Perle 494 -- MIDRANGE-L

Neil,

Sounds reasonable but...

This had been working for along time

The Perle tech specifically said that the only limits was twinax addresses (4
ports * 7 addresses = 28 PCs not sessions), and the QPCSUPP mode limit on
sessions per PC (set at 256 so no problem), and QUTOVRT (500) for total virtual
devices system wide automatically created (all virtual existed prior to problem
and no new ones needed to be created)

Thanks,

Roger Vicker, CCP.

Neil Palmer wrote:

> Multiple sessions are using multiple workstation addresses, and once you
> hit a total of 40 addresses attached to one controller no additional
> sessions can start.  You move the PC to another controller, with less than
> 40 active twinax addresses, and get connected.
>
> Neil Palmer      DPS Data Processing Services Canada Ltd.
> 50 Acadia Avenue, Ste.102                   AS/400~~~~~
> Markham, Ontario, Canada.   ____________          ___  ~
> Phone:(905) 474-4890 x303   |OOOOOOOOOO| ________  o|__||=
> Cell.:(416) 565-1682 x303   |__________|_|______|_|______)
> Fax:  (905) 474-4898         oo      oo   oo  oo   OOOo=o\
> mailto:NeilP@DPSlink.com  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> http://www.DPSlink.com     iSeries 400  The Ultimate Business Server
>
> "Roger Vicker, CCP" <rvicker@vicker.com>
> Sent by: owner-midrange-l@midrange.com
> 2001/01/12 19:29
> Please respond to MIDRANGE-L
>
>
>         To:     Midrange List <MIDRANGE-L@midrange.com>
>         cc:
>         Subject:        Experince with Perle 494
>
> Hello,
>
> Has anyone seen this strange one.
>
> Perle 494 with 5 twinax cards and at version 3.91, to a Vanguard 100
> router, to frame relay, to AS/400 620 V4R4M0.
>
> Multiple PCs using Client Access V3R2M0 and service pack SF64050,
> Perle/Affinity PCI Twinax Cards, twisted pair, and powered hubs. All
> this has been working fairly well for months. (Occasional session
> freeze/drop)
>
> Several PCs are connected to the AS/400. Another PC tries to connect
> but gets a message that there was a communications error while
> verifying security (or to that effect). If I move the PC to another
> port on the same controller I get the same thing. Move it to another
> controller and it gets in so the wire and card must be good.
>
> While this is going on some (but not all) of the users that are
> connected report that they can only get 2 or 3 sessions active. I
> watched as user 1 started A then B and tried C but got a blank screen.
> Then watched user 2, without anything else changed or ended, start A
> then B then C and get only a blank screen for D. To make this stranger
> still after user 3 couldn't get in at all, user 1 disconnected
> completely and then user 3 could connect but user 1 could no longer
> get in. Reverse it, user 3 disconnects and user 1 could connect.
>
> I checked the MODD QPCSUPP and it was set for 256/256. System value
> QUTORMT shouldn't be a problem because it was set at 500 and all the
> devices had been created a long time ago and had been in use before
> today.
>
> After several hours of chasing ghosts I shut down the Perle over
> lunch, varied everything off, powered up the Perle, and varied
> everything on. This let almost everyone that had problems in but a few
> are still limited to 1 session or having problems getting connected.
> Any Ideas would be greatly appreciated.
>
> I am about ready to tell them to shut the plant down for the 30 days
> left until Sprint delivers a new router so I can move them to CA
> Express over TCP.
>
> Roger Vicker, CCP
>

--
*** Vicker Programming and Service *** Have bits will byte *** www.vicker.com 
***

Please be sure to exit before leaving. - Jack Treger


+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---