Re: Experince with Perle 494 -- MIDRANGE-L

its been a while, but I beleive the
64 is because it will "negotiate" the smallest number
of either of the two LU's (logical units) talking to each other.
your mode is 256 session, but whatever it is talking
to must be 64 session.
There is also a Support Line doc
Maximum Number of Devices and Sessions on 5x94
that has table listing max devices for diff models.
hth-jim franz

----- Original Message -----
From: "Roger Vicker, CCP" <rvicker@vicker.com>
To: <MIDRANGE-L@midrange.com>
Sent: Sunday, January 14, 2001 12:37 PM
Subject: Re: Experince with Perle 494


> Larry,
>
> When the tech had me do a display on the Mode status for a couple of
active PCs it
> was showing an instance per PC since each is a virtual host. It actually
showed
> that the session limit had been "negotiated" to 64 per PC rather than the
"defined"
> 256.
>
> Roger Vicker, CCP
>
> Larry Bolhuis wrote:
>
> > > Multiple sessions are using multiple workstation addresses, and once
you
> > > hit a total of 40 addresses attached to one controller no additional
> > > sessions can start.  You move the PC to another controller, with less
than
> > > 40 active twinax addresses, and get connected.
> >
> >   Not quite correct. WIth CA Over twinax there is only ONE twinax
> > 'session' (address) active. Each session on the PC just uses another of
> > the available sessions in the active mode.  It certainly sounds like you
> > are hitting some type of limit for sure. If you have 5 twinax cards in
> > that thing (140 possible addresses) the number of sessions could easily
> > hit 256. What I can't remember is whether you get multiple instances of
> > mode QPCSUPP, one for each of the 5 cards in the perle or just one
> > instance.  If you check the mode status does it show that you have
> > sessions avilable?
> >
> >  - Larry
> >
> > >
> > > Neil Palmer      DPS Data Processing Services Canada Ltd.
> > > 50 Acadia Avenue, Ste.102                   AS/400~~~~~
> > > Markham, Ontario, Canada.   ____________          ___  ~
> > > Phone:(905) 474-4890 x303   |OOOOOOOOOO| ________  o|__||=
> > > Cell.:(416) 565-1682 x303   |__________|_|______|_|______)
> > > Fax:  (905) 474-4898         oo      oo   oo  oo   OOOo=o\
> > > mailto:NeilP@DPSlink.com  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> > > http://www.DPSlink.com     iSeries 400  The Ultimate Business Server
> > >
> > > "Roger Vicker, CCP" <rvicker@vicker.com>
> > > Sent by: owner-midrange-l@midrange.com
> > > 2001/01/12 19:29
> > > Please respond to MIDRANGE-L
> > >
> > >
> > >         To:     Midrange List <MIDRANGE-L@midrange.com>
> > >         cc:
> > >         Subject:        Experince with Perle 494
> > >
> > > Hello,
> > >
> > > Has anyone seen this strange one.
> > >
> > > Perle 494 with 5 twinax cards and at version 3.91, to a Vanguard 100
> > > router, to frame relay, to AS/400 620 V4R4M0.
> > >
> > > Multiple PCs using Client Access V3R2M0 and service pack SF64050,
> > > Perle/Affinity PCI Twinax Cards, twisted pair, and powered hubs. All
> > > this has been working fairly well for months. (Occasional session
> > > freeze/drop)
> > >
> > > Several PCs are connected to the AS/400. Another PC tries to connect
> > > but gets a message that there was a communications error while
> > > verifying security (or to that effect). If I move the PC to another
> > > port on the same controller I get the same thing. Move it to another
> > > controller and it gets in so the wire and card must be good.
> > >
> > > While this is going on some (but not all) of the users that are
> > > connected report that they can only get 2 or 3 sessions active. I
> > > watched as user 1 started A then B and tried C but got a blank screen.
> > > Then watched user 2, without anything else changed or ended, start A
> > > then B then C and get only a blank screen for D. To make this stranger
> > > still after user 3 couldn't get in at all, user 1 disconnected
> > > completely and then user 3 could connect but user 1 could no longer
> > > get in. Reverse it, user 3 disconnects and user 1 could connect.
> > >
> > > I checked the MODD QPCSUPP and it was set for 256/256. System value
> > > QUTORMT shouldn't be a problem because it was set at 500 and all the
> > > devices had been created a long time ago and had been in use before
> > > today.
> > >
> > > After several hours of chasing ghosts I shut down the Perle over
> > > lunch, varied everything off, powered up the Perle, and varied
> > > everything on. This let almost everyone that had problems in but a few
> > > are still limited to 1 session or having problems getting connected.
> > > Any Ideas would be greatly appreciated.
> > >
> > > I am about ready to tell them to shut the plant down for the 30 days
> > > left until Sprint delivers a new router so I can move them to CA
> > > Express over TCP.
> > >
> > > Roger Vicker, CCP
> > >
> >
> > --
> > Larry Bolhuis
> > Arbor Solutions, Inc.
> > (616) 451-2500
> > (616) 451-2571 -fax
> > lbolhuis@arbsol.com
>
> --
> *** Vicker Programming and Service *** Have bits will byte ***
www.vicker.com ***
> Please be sure to exit before leaving. - Jack Treger
>
>
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
david@midrange.com
> +---
>

+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---