|
midrange.com
Hi Duane,
Did you add the service program where you want to set the procedure
breakpoint to into debug? You could do it by two ways:
First way:
Use Debug (prompt) -> XXX to bring up the launch config dialog, and add the
(additional) program/service program you want to debug there. Then click
Debug botton.
Second way:
Bring up the debugger by debugging a program. Then, inside the debug
session, swith to Programs view, and use the "+" icon there to bring up the
Add Program dialog to add your service program, just like WDSC5.1.2.
Please let me know if you'd already done that. If not, if adding the
program/service program will make a difference. Thanks.
Regards,
Xuan Chen, Problem Determination Tools for iSeries
(905) 413-3769 T/L 969-3769
xuanchen@xxxxxxxxxx
"Christen, Duane
J."
<dchristen@mcleod To
usa.com> "'Websphere Development Studio
Sent by: Client for iSeries'"
wdsci-l-bounces@m <wdsci-l@xxxxxxxxxxxx>
idrange.com cc
Subject
12/07/2005 12:38 RE: [WDSCI-L] Where is verify
PM connection in 6.x
Please respond to
Websphere
Development
Studio Client for
iSeries
Xuan:
Version V5R2M0
RPG IV, Debug as...
None of the breakpoints have tails.
Duane Christen
-----Original Message-----
From: Xuan Chen [mailto:xuanchen@xxxxxxxxxx]
Sent: Wednesday, December 07, 2005 11:07 AM
To: Websphere Development Studio Client for iSeries
Subject: RE: [WDSCI-L] Where is verify connection in 6.x
Hi Duane,
Could you please provide me the following information?
iSeries Version
Language of the program/service program you want to debug
The steps you used to start your debug session (setting Service entry
point, or Debug as ...)
And also please check if the breakpoint you set in the procedure is just a
blue dot, or has a check mark on top of it (looks like it has a little
tail).
Thanks,
Xuan Chen, Problem Determination Tools for iSeries
(905) 413-3769 T/L 969-3769
xuanchen@xxxxxxxxxx
"Christen, Duane
J."
<dchristen@mcleod To
usa.com> "'Websphere Development Studio
Sent by: Client for iSeries'"
wdsci-l-bounces@m <wdsci-l@xxxxxxxxxxxx>
idrange.com cc
Subject
12/07/2005 11:16 RE: [WDSCI-L] Where is verify
AM connection in 6.x
Please respond to
Websphere
Development
Studio Client for
iSeries
WDSC 6.0.1 Build id: 20050725_1800
I am attempting to debug a process with multiple service programs and
underlying procedures. In the previous version of WDSC (5.1...) I could set
breakpoints within the lower lever procedures and click the resume
button/F8
and the process would stop on the break point in the lower level proc. With
WDSC 6.0.1 the break points are ignored, unless I step into the procedure
and then click resume/F8. Is there a "run to next breakpoint" or something
else that I am missing?
It is a real PITA having to step into 4 procedures just to get down to
where
I need to debug the process.
Duane Christen
P.S. The step over button/F6 function is also ignoring breakpoints which is
less of a problem but is still entirely unexpected.
NOTICE: This electronic mail transmission may contain confidential
information and is intended only for the person(s) named. Any use, copying
or disclosure by any other person is strictly prohibited. If you have
received this transmission in error, please notify the sender via e-mail.
--
This is the Websphere Development Studio Client for iSeries (WDSCI-L)
mailing list
To post a message email: WDSCI-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/wdsci-l.
--
This is the Websphere Development Studio Client for iSeries (WDSCI-L)
mailing list
To post a message email: WDSCI-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/wdsci-l.
NOTICE: This electronic mail transmission may contain confidential
information and is intended only for the person(s) named. Any use, copying
or disclosure by any other person is strictly prohibited. If you have
received this transmission in error, please notify the sender via e-mail.
--
This is the Websphere Development Studio Client for iSeries (WDSCI-L)
mailing list
To post a message email: WDSCI-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/wdsci-l.
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.
