Those of us that have dealt with the COD and VET codes in the past knew
where all that was (although finding it in the new HMC code was almost a
snipe hunt)
--
Jim Oberholtzer
Agile Technology Architects
-----Original Message-----
From: MIDRANGE-L <midrange-l-bounces@xxxxxxxxxxxx> On Behalf Of Rob Berendt
Sent: Tuesday, December 11, 2018 7:29 AM
To: Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>
Subject: RE: How does one apply a new UAK (Update Access Key)?
<snip>
Some HMC levels are supposed to be able to go out and get/apply the code for
you. I've tried to set that up and had limited success. Most times it does
not work.
</snip>
I tried Service Management, Connectivity, Electronic Service Agent Setup
Wizard, and did the connectivity test and that worked. Then I did Service
Management, Serviceability, Transmit Service Information, Update Access Key
Information, Send Now and .... nothing. That's when I dug deeper and found
COD.
Rob Berendt
--
IBM Certified System Administrator - IBM i 6.1 Group Dekko Dept 1600 Mail
to: 2505 Dekko Drive
Garrett, IN 46738
Ship to: Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com
From: "Jim Oberholtzer" <midrangel@xxxxxxxxxxxxxxxxx>
To: "'Midrange Systems Technical Discussion'"
<midrange-l@xxxxxxxxxxxx>
Date: 12/11/2018 08:10 AM
Subject: RE: How does one apply a new UAK (Update Access Key)?
Sent by: "MIDRANGE-L" <midrange-l-bounces@xxxxxxxxxxxx>
The system sends out messages both in IBM i and on the HMC when the date
is
getting close. If you monitor for the message, you can get the code and
update it within 5 minutes, problem gone.
Some HMC levels are supposed to be able to go out and get/apply the code
for
you. I've tried to set that up and had limited success. Most times it
does
not work.
--
Jim Oberholtzer
Agile Technology Architects
-----Original Message-----
From: MIDRANGE-L <midrange-l-bounces@xxxxxxxxxxxx> On Behalf Of Rob
Berendt
Sent: Tuesday, December 11, 2018 6:41 AM
To: Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>
Subject: Re: How does one apply a new UAK (Update Access Key)?
It's really only needed when you update firmware.
IDK how it's supposed to "notify" me but I just check it on a quarterly
basis. Or, subtract enough days from the current expiration date to give
me
time to check the maintenance contract and add that date on my calendar.
Rob Berendt
--
IBM Certified System Administrator - IBM i 6.1 Group Dekko Dept 1600 Mail
to: 2505 Dekko Drive
Garrett, IN 46738
Ship to: Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com
From: "Jack Kingsley" <iseriesflorida@xxxxxxxxx>
To: "Midrange Systems Technical Discussion" <midrange-l@xxxxxxxxxxxx>
Date: 12/11/2018 06:32 AM
Subject: Re: How does one apply a new UAK (Update Access Key)?
Sent by: "MIDRANGE-L" <midrange-l-bounces@xxxxxxxxxxxx>
Rob, curious question. If you didn't check this, how would the system
notify you of this in advance.
On Mon, Dec 10, 2018 at 3:25 PM Rob Berendt <rob@xxxxxxxxx> wrote:
I have a P8.
I am using HMC 9.
I used Systems, Action, Updates, View System Information and can see
when
the UAK expires.
I went to ESS, "My entitled hardware", "UAK - View, Download and Request
Keys" at https://www.ibm.com/servers/eserver/ess/ProtectedServlet.wss
and
requested a new key. It expires next June and gave me this long string
as
the key.
So far so good.
Now, how do I actually apply this key?
....
Argh! I keep forgetting "View" as in "View System Properties" on the
HMC
doesn't really mean just "view". It means view, update and otherwise
muck
around in here.
So I opened up my HMC 9. Go into All Systems, select the system,
Actions,
View System Properties, Capacity on Demand, CoD functions, Enter CoD
code,
and paste that new code here.
I used Systems, Action, Updates, View System Information and can see
when
the new UAK expires.
Just sharing in case anyone has to figure this out.
Rob Berendt
--
IBM Certified System Administrator - IBM i 6.1
Group Dekko
Dept 1600
Mail to: 2505 Dekko Drive
Garrett, IN 46738
Ship to: Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: https://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at https://archive.midrange.com/midrange-l.
Please contact support@xxxxxxxxxxxx for any subscription related
questions.
Help support midrange.com by shopping at amazon.com with our affiliate
link: https://amazon.midrange.com
midrange.com
