Rob, single tape device.

On Thu, Apr 26, 2012 at 11:40 AM, <rob@xxxxxxxxx> wrote:

I'm trying to determine what he is trying to do.
Is he using a tape library or a tape device?
I suspect he is using a tape library, configured sequentially as a tape
device. And what is happening is that his backup is taking more than one
tape. He doesn't want it placed in the I/O slot(s) when the tape fills,
instead he wants to to go back into the library. Perhaps it takes more
than 2 tapes and he only has one I/O slot. Those of us with 18 I/O slots
have to remember those without.

ENDOPT is not pertinent to this as that only says what to do with the last
tape when the save completes, not what to do when the tape fills.

Ideally he would leave the darn thing as a media library, load up BRMS and
configure that. It took me a LOT of cajoling to be assimilated into the
BRMS realm. But now that I'm there, I like it.

I might be tempted to delve into QSYSOPR or DSPLOG and see the messages in
the CPA4088 genre and see if there's some way to control what happens when
the tape fills. But I don't think you can. From the help on ENDOPT:

Specifies the operation that is automatically done on the tape or
optical volume after the save operation ends. If more than one
volume is used, this parameter applies only to the last volume used;
all other volumes are unloaded when the end of the volume is
reached.



Rob Berendt
--
Group Dekko
Dept 1600
Mail to: 2505 Dekko Drive
Garrett, IN 46738
Ship to: Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com





From: Jim Oberholtzer <midrangel@xxxxxxxxxxxxxxxxx>
To: Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>,
Date: 04/26/2012 11:21 AM
Subject: Re: option 21 save/end of tape option ?
Sent by: midrange-l-bounces@xxxxxxxxxxxx



The actual CL program that is running is QMNSAVE. You can retrieve the
CL source.

You'll find the save commands if you search for them. Every ENDOPT()
parameter that I was able to find is set to *LEAVE (V7R1).

In any case you can always modify the program and put the default you
wish in there. You can also preface it with "??" to cause the prompt to
come up if the program is set to prompt. (an option on the 21 save)

Jim Oberholtzer
Chief Technical Architect
Agile Technology Architects


On 4/26/2012 9:23 AM, Jack Kingsley wrote:
Does anyone know where it gets this from, it would appear that the
default
is always UNLOAD. I don't see this as an option on the 21 screen, I
want
to sometimes use rewind.
--
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.


--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.



This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2019 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].