• Subject: RE: Save breakpoints in Source Debug
  • From: Buck Calabro/commsoft<mcalabro@xxxxxxxxxxxx>
  • Date: Tue, 5 Jan 1999 09:32:48 -0500

If you sort the "All Books" bookshelf by title, the exact title (V3R7) is 
"Interactive Source Debugger".

Basically, issue a SET LOG ON to log your commands;
ISDB will log your commands to QIXALOG.

Use SEU to copy the commands you want from QIXALOG
into another file.  Re-issue those commands by USE filename.

QIXAPROF is used every time you STRISDB, so you can put
your personal favourites (equates, etc.) there.

QIXALOG gets cleared when you run STRISDB.

Buck Calabro
CommSoft, Albany, NY
mailto:mcalabro@commsoft.net





eric <eric@norcov.com> on 01/04/99 05:08:13 PM
Please respond to MIDRANGE-L@midrange.com
To:     "'MIDRANGE-L@midrange.com'" <MIDRANGE-L@midrange.com>
cc: 
Subject:        RE: Save breakpoints in Source Debug

Is that in Book Manager. I ran a search but did not find it.

Eric Kempter
CommAir Mechanical Services, Inc.


-----Original Message-----
From:   Simon Coulter [SMTP:shc@flybynight.com.au]
Sent:   Friday, January 01, 1999 4:40 PM
To:     MIDRANGE-L@midrange.com
Subject:        Re: Save breakpoints in Source Debug

Hello Ravi,

Yes, it is possible.  Read section 2.6 of the Interactive Source Debugger 
manual SC09-1897.

Regards,
Simon Coulter.

//----------------------------------------------------------
// FlyByNight Software         AS/400 Technical Specialists
// Phone: +61 3 9419 0175      Mobile: +61 0411 091 400
// Fax:   +61 3 9419 0175      E-mail: shc@flybynight.com.au
// 
// Windoze should not be open at Warp speed.
//--- forwarded letter 
-------------------------------------------------------
> X-Mailer: Mozilla 3.01 (Win95; I)
> Date: Wed, 30 Dec 98 17:31:39 -0600
> From: "Ravi" <ravi@spacestar.com>
> To: MIDRANGE-L@midrange.com
> Reply-To: MIDRANGE-L@midrange.com
> Subject: Save breakpoints in Source Debug

> 
> IS it possible to save the breakpoints set up in ISDB and then invoke
> the same break points in a later session? ISDB creates files QIXALOG,
> QIXAMPF in QTEMP. When breakpoints are added they must be stored in one
> of these files. During the debug session, I don't find any entries in
> these files, and maybe when the program ends the files are cleared out.
> Any ideas??
> 
> Thanks
> 
> Ravi



+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---


This thread ...


Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2019 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available here. If you have questions about this, please contact [javascript protected email address].