RE: News/400 Paging Program

["Leland, David" <dleland@xxxxxxxxxx>]

Well, I have all my line and controller descriptions right, so it must
be in the setup of the modem.  I've tried every combination of switch
settings I could think of (the manual isn't much help).  I just cannot
get the modem to autodial.

Is anyone out there using a 7852-400 modem in connection with the
New/400 paging program?

Dave

>----------
>From:  Carl Galgano[SMTP:cgalgano@ediconsulting.com]
>Sent:  Monday, July 28, 1997 10:34 AM
>To:    MIDRANGE-L@midrange.com; 'MIDRANGE-L@midrange.com'
>Subject:       Re: News/400 Paging Program
>
>Dave:
>Be sure the modem is set to use a V25bis autodial std.  Also check the
>line
>description to be sure autodial is set to *yes and dial type is set to
>*v25bis.  On the controller description, be sure the initial connection
>parm
>is set to *dial and the dial initiation parm is set to *Immed.
>Hope this helps.
>Carl
>
>At 10:05 AM 7/24/97 -0500, Leland, David wrote:
>>We recently went to a RISC box and in the process went from the old 2400
>>Baud IBM modem for ECS to a new 7852-400.  The new modem works great for
>>ECS but I cannot get it to work with our PAGER program.  Our PAGER
>>program is the one from the News/400 magazine that simply varys on a
>>line and controller (after setting up the phone number to be dialed on
>>the controller description), and waits a few seconds and varys
>>everything off.
>>
>>Our problem is that the new 7852-400 does not autodial when the
>>controller is varied on, as the old 2400 baud modem did.  Since we
>>carried over all our configuration descriptions from our old CISC box, I
>>figured it should work as before, but it doesn't.  I did check to make
>>sure that AUTODIAL was on and it is.
>>
>>When I do a SNDPTFORD, I can see and hear the new modem dial, however
>>when I try to use our PAGER program, the modem does not dial.
>>
>>Anyone have any thoughts on how to get this new modem to autodial?
>>
>>Thanks,
>>Dave
>>
>>* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
>>* This is the Midrange System Mailing List!  To submit a new message,   *
>>* send your mail to "MIDRANGE-L@midrange.com".  To unsubscribe from     *
>>* this list send email to MAJORDOMO@midrange.com and specify            *
>>* 'unsubscribe MIDRANGE-L' in the body of your message.  Questions      *
>>* should be directed to the list owner / operator: david@midrange.com   *
>>* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
>>
>Carl J. Galgano
>cgalgano@ediconsulting.com
>EDI Consulting Services, Inc.  
>540 Powder Springs Street
>Suite C19
>Marietta, GA 30064
>770-422-2995
>
>* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
>*
>* This is the Midrange System Mailing List!  To submit a new message,  
>*
>* send your mail to "MIDRANGE-L@midrange.com".  To unsubscribe from    
>*
>* this list send email to MAJORDOMO@midrange.com and specify           
>*
>* 'unsubscribe MIDRANGE-L' in the body of your message.  Questions     
>*
>* should be directed to the list owner / operator: david@midrange.com  
>*
>* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
>*
>umidr
>
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* This is the Midrange System Mailing List!  To submit a new message,   *
* send your mail to "MIDRANGE-L@midrange.com".  To unsubscribe from     *
* this list send email to MAJORDOMO@midrange.com and specify            *
* 'unsubscribe MIDRANGE-L' in the body of your message.  Questions      *
* should be directed to the list owner / operator: david@midrange.com   *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *