|
midrange.com
Thanks, Rob.
You'll have to remind me how to access the joblog after the job is
complete, if it's still available somewhere. There's no error code in
server log, just what I reported earlier.
You are correct in that QNOTES does not have *JOBCTL, but I'm assuming it
never has if it doesn't now because no one's changed it. However, the
program is running with the authority of the same profile that I'm using
when I successfully start the server manually. This other profile does
have *JOBCTL. Is using the QNOTES profile a requirement because it is
being started via CL?
Patrick
rob@xxxxxxxxx
Sent by:
domino400-bounces To
+ptrapp=nex-tech. Lotus Domino on the iSeries / AS400
com@xxxxxxxxxxxx <domino400@xxxxxxxxxxxx>
cc
08/11/2006 10:34 Subject
AM Re: Restarting QuickPlace server /
Starting QP via CL
Please respond to
Lotus Domino on
the iSeries /
AS400
<domino400@midran
ge.com>
I start our QP server nightly.
I did a DSPMSGD RANGE(LNT0920) MSGF(QNOTES/QLTBASEMS6) and it looks like
I'd need more information from the joblog. Most importantly, the error
code.
Hint: CHGUSRPRF QNOTES and give it *JOBCTL. Also have the subprogram
that starts it adopt authority of QNOTES. Put the CHGUSRPRF QNOTES in
your list of tasks to do everytime you put on a Notes upgrade.
Message ID . . . . . . . . . : LNT0920
Message file . . . . . . . . : QLTBASEMS6
Library . . . . . . . . . : QNOTES
Message . . . . : Error &1 has occurred, server not started
Cause . . . . . : An error has occurred trying to start the Domino
server
&5, the error code is &1:
-- 1 = Not authorized to use the STRDOMSVR command.
-- 2 = Error retrieving subsystem name.
-- 3 = Error retrieving security information. Message ID is &2.
-- 4 = Error retrieving subsystem information. Message ID is &2.
Subsystem is &4/&3.
-- 5 = Error starting subsystem &4/&3.
-- 6 = Error submitting a job to the subsystem &4/&3.
-- 7 = Error retrieving server information.
-- 8 = Error validating the server name.
-- 9 = Server is in a *STANDBY state
-- 10 = Server is being saved.
Recovery . . . :
-- 1 You need at least *JOBCTL to use this command. See your system
administrator.
-- 2 - 6 Save this job log and contact your service representative.
-- 7 - 8 The server name, &5, is probably not correct. Enter a
configured
server name and try the command again. If the server name is valid and
configured, then save the job log and contact your service
representative.
-- 9 The server is configured as part of a Domino application Cluster
Resource Group (CRG) &6. It is in *STANDBY state when application CRG &6
is
not primary (active) on this cluster node. The application CRG can be
started with a STRDOMCRG command. If the server's application CRG is
already
started its active primary cluster node can be changed to this system
using
the CHGDOMPRI command. Then try the request again.
-- 10 The server is being saved by another job on this system. The
server
cannot be started until this operation is complete. When the save of the
server completes try the request again.
Technical description . . . . . . . . : Errors have occurred and
processing
can not continue.
Rob Berendt
--
Group Dekko Services, LLC
Dept 01.073
PO Box 2000
Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com
"Patrick Trapp" <ptrapp@xxxxxxxxxxxx>
Sent by: domino400-bounces+rob=dekko.com@xxxxxxxxxxxx
08/11/2006 10:18 AM
Please respond to
Lotus Domino on the iSeries / AS400 <domino400@xxxxxxxxxxxx>
To
domino400@xxxxxxxxxxxx
cc
Subject
Restarting QuickPlace server / Starting QP via CL
I have a lightly-used QuickPlace server that was recently moved to a DPAR
on my iSeries.
I tried to create a CL program to end and restart the QuickPlace server so
I could do it after hours on a schedule, but I'm getting an error that I
have not found documentation for (even Google failed me this time). The
error showing in the job log is
Function check. LNT0920 unmonitored by RESTRQPPGM at statement 3200,
instruction X'0039'.
Statement 3200 in the CL program, assuming that is the one referred to in
the error, is
STRDOMSVR SERVER(QPPROD1) JSC(*NO)
The line before this command is a DLYJOB set to run for 180 seconds. I
can
run the same command from the command line and it runs (as far as I can
tell) perfectly. I'm not even sure where to look -- the details for the
error above are the standard CPF9999 which basically tells me to look at
the previous errors, but there are no previous errors. Any suggestions on
where I should look are much appreciated.
------------------------------------
Second question, related to the first, is how often do you restart your
QuickPlace server? Like I said, this one is very lightly used and is a
partition on our primary server. The server itself is IPLd rarely,
basically when we do full system saves, but the primary partition is shut
down every night to accommodate the backup procedure we are using. A
Sametime partition is in the works, so I will have the same question for
it, but there's some work to be done before I'm ready for that. Both of
these are 6.5.1 with the appropriate code updates / patches necessary to
run on a 6.5.4 server.
------------------------------------
Thanks,
Patrick
_______________________________________________
This is the Lotus Domino on the iSeries / AS400 (Domino400) mailing list
To post a message email: Domino400@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/domino400
or email: Domino400-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/domino400.
_______________________________________________
This is the Lotus Domino on the iSeries / AS400 (Domino400) mailing list
To post a message email: Domino400@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/domino400
or email: Domino400-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/domino400.
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.
