|
midrange.com
Hi Matt,
Good point. We actually plan to do something about this 'problem' in the
next release
of the iSeries debug tooling :-)
Regards,
Vadim.
MWHopkins@pdpgroupi
nc.com To: CODE/400 Discussion
& Support <code400-l@midrange.com>
Sent by: cc:
code400-l-bounces@m Subject: Re: Debug question
idrange.com
01/16/2003 10:53 AM
Please respond to
CODE/400 Discussion
& Support
I figured out what I was doing wrong... The OPM was not compiled with
*SRCDBG. This then gave me the message: "Error occurred: Host: CPF9584 OPM
program PGMC cannot be added to ILE debug environment. "
Now if I had looked at the second level text of the CPF message before, I
would have known what was wrong...
Message . . . . : OPM program &1 cannot be added to ILE debug
environment.
Cause . . . . . : Program &1 in library &2 cannot be added to the ILE
debug
environment because it does not contain OPM source debug data. If you
want
to debug an OPM program in the ILE debug environment, it must contain
OPM
source debug data.
Recovery . . . : If your OPM compiler supports generating source debug
data, compile the program by specifying the appropriate compile option.
Then, add the program to debug again. The OPM source debug data is
specified
at compile time using the OPTION parameter in either of two ways:
1) For CRTRPGPGM, CRTCBLPGM, and CRTCLPGM: specify OPTION(*SRCDBG).
2) For CRTRPGPGM, CRTCBLPGM, CRTRPTPGM, CRTSQLRPG, CRTSQLCBL, and
CRTCICSCBL: specify OPTION(*LSTDBG).
Thanks for the prod to look further, which I should have done first :o
Matt
berestet@ca.ibm.com
Sent by: code400-l-bounces@midrange.com
01/16/2003 10:19 AM
Please respond to CODE/400 Discussion & Support
To: CODE/400 Discussion & Support <code400-l@midrange.com>
cc:
Subject: Re: Debug question
Hi Matt,
Actually, the Distributed Debugger supports debugging of either OPM or ILE
programs.
Combinations should work fine as well. As a matter of fact, you don't
really need to specify
anything differently depending on what program type you are trying to
debug.
So, your scenario should work just fine in the Distributed Debugger.
Hope this helps,
Vadim Berestetsky
Distributed Debugger Development
MWHopkins@pdpgroupi
nc.com To: CODE/400
Discussion & Support <code400-l@midrange.com>
Sent by: cc:
code400-l-bounces@m Subject: Debug question
idrange.com
01/16/2003 09:39 AM
Please respond to
CODE/400 Discussion
& Support
Is there a way to use the Distributed Debugger to debug both OPM & ILE
programs within the same job?
Example: PgmA is a CL that calls PgmB an ILE rpg, then calls PgmC an OPM
rpg. I want to watch what happens in PgmB then PgmC while in the
Distributed Debugger.
Thanks,
Matt Hopkins
PDP Group, Inc
Voice: 410-584-0330
PO Box 650001
Fax: 410-584-0336
Hunt Valley, MD 21065-0001
e-mail: MWHopkins@PDPGroupInc.Com
_______________________________________________
This is the CODE/400 Discussion & Support (CODE400-L) mailing list
To post a message email: CODE400-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo.cgi/code400-l
or email: CODE400-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/code400-l.
NOTE: WDSc for iSeries disucssion has it's own mailing list.
Information can be found at
http://lists.midrange.com/cgi-bin/listinfo/wdsc-l
_______________________________________________
This is the CODE/400 Discussion & Support (CODE400-L) mailing list
To post a message email: CODE400-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo.cgi/code400-l
or email: CODE400-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/code400-l.
NOTE: WDSc for iSeries disucssion has it's own mailing list.
Information can be found at
http://lists.midrange.com/cgi-bin/listinfo/wdsc-l
_______________________________________________
This is the CODE/400 Discussion & Support (CODE400-L) mailing list
To post a message email: CODE400-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo.cgi/code400-l
or email: CODE400-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/code400-l.
NOTE: WDSc for iSeries disucssion has it's own mailing list.
Information can be found at
http://lists.midrange.com/cgi-bin/listinfo/wdsc-l
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.
