Re: Debug question -- CODE400-L

I figured out what I was doing wrong... The OPM was not compiled with 
*SRCDBG. This then gave me the message: "Error occurred: Host: CPF9584 OPM 
program PGMC cannot be added to ILE debug environment. "

Now if I had looked at the second level text of the CPF message before, I 
would have known what was wrong...

Message . . . . :   OPM program &1 cannot be added to ILE debug 
environment. 
Cause . . . . . :   Program &1 in library &2 cannot be added to the ILE 
debug 
  environment because it does not contain OPM source debug data. If you 
want 
  to debug an OPM program in the ILE debug environment, it must contain 
OPM 
  source debug data.  
Recovery  . . . :   If your OPM compiler supports generating source debug  
 
  data, compile the program by specifying the appropriate compile option.  
 
  Then, add the program to debug again. The OPM source debug data is 
specified
  at compile time using the OPTION parameter in either of two ways:  
    1) For CRTRPGPGM, CRTCBLPGM, and CRTCLPGM: specify OPTION(*SRCDBG).  
    2) For CRTRPGPGM, CRTCBLPGM, CRTRPTPGM, CRTSQLRPG, CRTSQLCBL, and  
  CRTCICSCBL: specify OPTION(*LSTDBG).  

Thanks for the prod to look further, which I should have done first :o

Matt






berestet@ca.ibm.com
Sent by: code400-l-bounces@midrange.com
01/16/2003 10:19 AM
Please respond to CODE/400 Discussion & Support

 
        To:     CODE/400 Discussion & Support <code400-l@midrange.com>
        cc: 
        Subject:        Re: Debug question


Hi Matt,

Actually, the Distributed Debugger supports debugging of either OPM or ILE
programs.
Combinations should work fine as well. As a matter of fact, you don't
really need to specify
anything differently depending on what program type you are trying to
debug.

So, your scenario should work just fine in the Distributed Debugger.

Hope this helps,
Vadim Berestetsky
Distributed Debugger Development



   
                      MWHopkins@pdpgroupi    
                      nc.com                     To:       CODE/400 
Discussion & Support <code400-l@midrange.com>  
                      Sent by:                   cc:     
                      code400-l-bounces@m        Subject:  Debug question  
 
                      idrange.com   
   
   
                      01/16/2003 09:39 AM    
                      Please respond to    
                      CODE/400 Discussion    
                      & Support   
   
   



Is there a way to use the Distributed Debugger to debug both OPM & ILE
programs within the same job?

Example: PgmA is a CL that calls PgmB an ILE rpg, then calls PgmC an OPM
rpg. I want to watch what happens in PgmB then PgmC while in the
Distributed Debugger.

Thanks,


Matt Hopkins

PDP Group, Inc
Voice: 410-584-0330

PO Box 650001
Fax: 410-584-0336

Hunt Valley, MD 21065-0001
e-mail: MWHopkins@PDPGroupInc.Com
_______________________________________________
This is the CODE/400 Discussion & Support (CODE400-L) mailing list
To post a message email: CODE400-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo.cgi/code400-l
or email: CODE400-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/code400-l.

NOTE: WDSc for iSeries disucssion has it's own mailing list.
Information can be found at
http://lists.midrange.com/cgi-bin/listinfo/wdsc-l




_______________________________________________
This is the CODE/400 Discussion & Support (CODE400-L) mailing list
To post a message email: CODE400-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo.cgi/code400-l
or email: CODE400-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/code400-l.

NOTE: WDSc for iSeries disucssion has it's own mailing list.
Information can be found at http://lists.midrange.com/cgi-bin/listinfo/wdsc-l