RE: Changes lost after receiving "Member locked" message

["Phil" <sublime78ska@xxxxxxxxx>]

Reeve,

I use the same router and STRCODE works for me.  BUT, I did have a problem
once and here's what I did to correct it.  I had to add ports in the port
forwarding option.  The problem arised because of dhcp & the ports being
forwarded were to a specific ip address.  In my case it was just as easy for
me to turn on a particular PC first but otherwise disable DHCP.

I don't open files on the host because for me it's quicker to use CPO so I
don't know if I have this problem at home - just at work.

hth,

Phil

> -----Original Message-----
> From: code400-l-admin@midrange.com
> [mailto:code400-l-admin@midrange.com]On Behalf Of Reeve Fritchman
> Sent: Thursday, February 28, 2002 10:12 AM
> To: code400-l@midrange.com
> Subject: RE: Changes lost after receiving "Member locked" message
>
>
> A clarification: when I'm in the office, I'm using a Netgear RT-314
> connection sharing device (it provides NAT service) to connect
> three PC's to
> my cable modem.  I can't figure out how to get the iSeries STRCODE command
> to work in this environment (I think the NAT is screwing things up) so I
> rely on the PC-based communications daemon.  This was the
> environment  where
> the "Member locked" problem occurred.
>
> When I'm away from the office and dialed in, STRCODE works fine and I can
> use PDM to initiate CODE/400 functions.  Usually right-clicking on the
> communications daemon terminates the STRCODE function normally.
>
> -rf
>
> -----Original Message-----
> From: code400-l-admin@midrange.com [mailto:code400-l-admin@midrange.com]On
> Behalf Of Phil Groschwitz
> Sent: Thursday, February 28, 2002 8:48 AM
> To: code400-l@midrange.com
> Subject: RE: Changes lost after receiving "Member locked" message
>
> >
> > Reeve: was that you cannot kill the daemon when it
> > was locked?
> > I agree. There are still more work for me on this
> > data lost problem. I
> > appreciate your feedback.
> >
> Here's some feedback:
>
> Sometimes when editing a source file on the host with
> CODE, after closing the editor the STRCODE job still
> has a lock on the member.  I can reopen it in CODE but
> not in SEU.  The only way I've found to get rid of the
> lock is to end the STRCODE server and signoff.
>
> Phil
>
> __________________________________________________
> Do You Yahoo!?
> Yahoo! Greetings - Send FREE e-cards for every occasion!
> http://greetings.yahoo.com
> _______________________________________________
> This is the CODE/400 Discussion & Support (CODE400-L) mailing list
> To post a message email: CODE400-L@midrange.com
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/cgi-bin/listinfo/code400-l
> or email: CODE400-L-request@midrange.com
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/code400-l.
>
> _______________________________________________
> This is the CODE/400 Discussion & Support (CODE400-L) mailing list
> To post a message email: CODE400-L@midrange.com
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/cgi-bin/listinfo/code400-l
> or email: CODE400-L-request@midrange.com
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/code400-l.
>


_________________________________________________________
Do You Yahoo!?
Get your free @yahoo.com address at http://mail.yahoo.com