Thank you Rob!
Currently I am watching the status codes on the control panel.
The power light is solid green.
After a few minutes off jet fans they have gone a little more quiet.
The Attention light turned yellow/orange.
The code is now showing now is B6000901.
B6000901
Explanation
The LinkLoader has found its bad flag ON.
Response
This reference code is usually the result of a system termination while the LinkLoader is performing its work.
Reinstall the Licensed Internal Code by using Utilities to install and restore IBM i Licensed Internal Code .
Guess there is more reading to do today.
-----Original Message-----
From: MIDRANGE-L [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of rob@xxxxxxxxx
Sent: Thursday, January 21, 2016 8:54 AM
To: Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>
Subject: RE: No system console and TCP/IP down
Your Model May Vary (YMMV)
However, according to this:
http://www-01.ibm.com/support/knowledgecenter/8286-41A/p8haj/p8haj_controlpanel.htm
A flashing green power light means the unit has power but it is in standby mode. Basically, it is powered off! This will have a drastic effect on the behavior of TCP/IP (to say the least).
Did you ever do the functions I suggested to get it to display your console type?
Using the console service functions (65+21)
https://www-01.ibm.com/support/knowledgecenter/ssw_ibm_i_71/rzajr/rzajrfunctions6521.htm?lang=en-us
Yes, it is sad that
IBM i 7.2>Basic system operations>Starting and stopping the
system>Starting the system>
Assumes that the system is already started.
Then again, this is not an AS/400. It is a Power system running IBM i.
One cannot assume that IBM i is the only OS on it and that there is only one lpar of IBM i. Therefore you have to go into the "Hardware Information Center"
http://www-01.ibm.com/support/knowledgecenter/
Expand "Power Systems"
Figure out what genre you have, Power 6 for example. And verify that by expanding it and seeing if your model is in it.
Even if you go through all this, you will not find "How to start this BAMF up".
Normally one attaches a Lan Console, or an HMC, to one of these and uses that to start it up.
So the trick is, you expand the section "Working with consoles, terminals, and interfaces for POWER... processor-based systems" where ... is the genre of Power system you are running. That's about the only time you touch the buttons. (Yes, I'm back to that...) This is where I went to get the explanation of the light.
Rob Berendt
--
IBM Certified System Administrator - IBM i 6.1 Group Dekko Dept 1600 Mail to: 2505 Dekko Drive
Garrett, IN 46738
Ship to: Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com
From: "Hopkins, William" <William.Hopkins@xxxxxxxxxxxxxxxxx>
To: Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>
Date: 01/21/2016 08:29 AM
Subject: RE: No system console and TCP/IP down
Sent by: "MIDRANGE-L" <midrange-l-bounces@xxxxxxxxxxxx>
Evan,
The green power status indicator on the front control panel is flashing.
-----Original Message-----
From: MIDRANGE-L [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
Evan Harris
Sent: Wednesday, January 20, 2016 2:16 PM
To: Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>
Subject: Re: No system console and TCP/IP down
Hi WIlliam
Is there a green light on the front of the box ? If so it it flashing or
on light up solid ?
On Thu, Jan 21, 2016 at 6:14 AM, Hopkins, William <
William.Hopkins@xxxxxxxxxxxxxxxxx> wrote:
Thanks for confirming that Chris.
So back to the question...
When the function 2 is set to manual mode= 'M', why does the control
panel not show function 3?
-----Original Message-----
From: MIDRANGE-L [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
Chris Bipes
Sent: Wednesday, January 20, 2016 12:10 PM
To: 'Midrange Systems Technical Discussion' <midrange-l@xxxxxxxxxxxx>
Subject: RE: No system console and TCP/IP down
No a 710 does not have a key. You can stop looking for the key.
Chris Bipes
Director of Information Services
CrossCheck, Inc.
-----Original Message-----
From: MIDRANGE-L [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
Hopkins, William
Sent: Wednesday, January 20, 2016 8:59 AM
To: Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>
Subject: RE: No system console and TCP/IP down
Thanks Chris
I just read this in the document provided yesterday.
1. If your system uses a keystick, insert it in the key slot.
So I used those terms.
2. Place the system into manual mode by using the system's control
panel.
I do not think there is one on the IBMi Power 710 Express.
But when I changed function 2 to be manual = "M" and the function 3
did not become available.
I started thinking there might be one I am not seeing and it was not
allowing the change to go through without one.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take
a moment to review the archives at
http://archive.midrange.com/midrange-l.
Please contact support@xxxxxxxxxxxx for any subscription related
questions.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take
a moment to review the archives at
http://archive.midrange.com/midrange-l.
Please contact support@xxxxxxxxxxxx for any subscription related
questions.
As an Amazon Associate we earn from qualifying purchases.