Re: Permanent I/O Error occured to DSPF

Device class . . . . . . . . . . . : *VRT
Device type . . . . . . . . . . . : 3477
Device model . . . . . . . . . . . : FC

Now interestingly enough, I get the error when using IBM's Client
Access; however if I use Powerterm, I don't get the error. The device
description is the same in either case.

Device class . . . . . . . . . . . : *VRT
Device type . . . . . . . . . . . : 3477
Device model . . . . . . . . . . . : FC

Charles

On Thu, Oct 9, 2008 at 11:00 AM, Terrence Enger <tenger@xxxxxxxxxxxxxxxx> wrote:

Charles,

<aside attitued="picked_upon"> Sigh! I started out to write what I
thought I remembered which might be helpful. Then I created a DDS file
to prove that I was, as it turned out, wrong. Then I went to the
infocenter to check a manual. Then I created and tested (STRSDA 3) a
format with 800 "both" fields. Infocenter is *still* loading. </aside>

DDS-defined dspf, right?

What is the device type where the error occurred?

Cheers,
Terry.

P.S.: Infocenter is *still* loading.


On Wed, 2008-10-08 at 16:59 -0400, Charles Wilt wrote:

All, I'm getting an error during I/O to a display file:


RNQ1251

Message . . . . : Permanent I/O error occurred in file FV011RP (C G D F).
Cause . . . . . : RPG procedure FV011R in program HLTHCURRLS/FV011R at
statement 11288 detected a permanent (not recoverable) file, session, or
device error. The session, device and/or program has been stopped. Examine
the major/minor return code value to determine the specific error that
occurred. If the major return code is 80 then a system or file error
occurred and programmer action is required to fix the problem. If the major
return code is 81 then a session or device error occurred, but use of
Technical description . . . . . . . . : The major return code is 80. The
minor return code is C0.

CPF5192
Message . . . . : Data sent to device QPADEV001X not valid. Negative
response code is 10050129.
Cause . . . . . : The condition was caused by the program output data
containing below hex 40 or too many input fields. More information on the
negative response code can be found in either the IBM 5494 Remote Control
Unit Functions Reference (under negative responses) or the SNA Formats
Manual (under SENSE or LUSTAT codes). Invalid data (below hex 40) may have
occurred in one of the following ways:
Invalid parameter data passed in variable to command language program.
Variable is used in SNDPGMMSG command. Command fails when data is
displayed.
Hexadecimal characters below hex 40 entered into TEXT parameter of create
command. Display command for object fails when object parameters are
displayed.
Data base record containing invalid data displayed by the application
program.
Failure to specify RSTDSP(*YES) when alternating displays from more than
one file to the device, where both files have input fields.

I've looked at the dump, I don't see any invalid characters (< x'40').

I looked up the sense code and it says:
10050129 = Format table overflow

Does anybody have an idea of what's wrong?

Thanks!

Charles Wilt

--
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.