× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.


  • Subject: Re: "RUNRMTCMD" on NT Server
  • From: Rob Berendt <rob@xxxxxxxxx>
  • Date: Thu, 25 May 2000 11:08:08 -0500

Load up the freebie FTP server that comes with NT.  
Then use a CLP to pipe some FTP subcommands.  I think 
you are looking for quote rcmd.  If you have further 
questions, please ask.





mullerj@nabiscosa.co.za on 05/25/2000 09:42:08 AM
Please respond to RPG400-L@midrange.com@Internet
To:     RPG400-L@midrange.com@Internet
cc:      
Fax to: 
Subject:        "RUNRMTCMD" on NT Server

I need to initiate a batch job (.BAT) on our NT Server from a CL program on
the AS400. When running a remote command from the AS400 to a PC with Win9x
and Client Access (4.3 & 4.4) the batch job runs perfectly. My problem is
that I cannot do the same on our NT Server. The error message produced is
the same as for a workstation when a user has not been granted remote access
or when the deamon has not been started ("Required user id is either missing
or invalid."). I have noticed the following differences between Client
Access on the PC and the NT Server - 

1. When running "cwbrxd" on the workstation the deamon will start and then
wait for incoming commands to process. On the server you will be returned to
the prompt after a while. Does this mean that the deamon is not running? Is
there another command that must be run for NT Server instead of "cwbrxd"? 

2. There is a Client Access Remote Command service running on the server.
What is this service for? Is it not maybe the "replacement" for CWBRXD?

3. On the Client Access Properties screen there is a "Incoming Remote
Command" (from where you can authorize system/user access) tab on the PC.
This tab does not appear on the Client Access Properties screen on the
server. Where do I authorize my AS400 or a user access to execute remote
commands on the NT Server?

Is it at all possible to run remote commands on a NT SERVER from the AS400?
Is there any other way to execute a batch job on the SERVER from the AS400
other than using RUNRMTCMD? Any help would be greatly appreciated.

Thanks,
Jan.
+---
| This is the RPG/400 Mailing List!
| To submit a new message, send your mail to RPG400-L@midrange.com.
| To subscribe to this list send email to RPG400-L-SUB@midrange.com.
| To unsubscribe from this list send email to RPG400-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---


+---
| This is the RPG/400 Mailing List!
| To submit a new message, send your mail to RPG400-L@midrange.com.
| To subscribe to this list send email to RPG400-L-SUB@midrange.com.
| To unsubscribe from this list send email to RPG400-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---

As an Amazon Associate we earn from qualifying purchases.

This thread ...


Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.