RE: Cat 5 cable RJ-45 connection HELP!

I've terminated a few Ethernet cables on the production floor here at ECHO
using a 110 punch down tool.  I was lucky enough to have our network guy
show me how it's done.  We are the only two here who know how to do it.  The
other network guy and the plant electrician don't know how.

It's not rocket science.  I'm color blind.

Bryan Burns
ECHO Incorporated    

-----Original Message-----
From: daparnin@xxxxxxxxxxxxxx [mailto:daparnin@xxxxxxxxxxxxxx]
Sent: Tuesday, November 01, 2005 9:55 AM
To: PC Technical Discussion for iSeries Users
Subject: Re: [PCTECH] Cat 5 cable RJ-45 connection HELP!






The web site that you referenced looks good.  You line up the wires while
holding them securly and slide the jack over them and then crimp.  If you
mess it up you chop the end off, get another jack, and try again.  After
awhile you get the hang of it.  If you have a commercially available patch
cord available you can look at it to see how the colors line up.  You may
find that they use other colors such as green, blue, yellow, and red.

Personally, I prefer wall plates with the snap-in jacks.  They show on the
jack itself which wire goes where.  I believe that I used Leviton when I
finished my basement about a decade ago.  If you go that route you will
need a punch-down tool with a 110 (if I recall correctly) blade.  I like
the clean look better than a hole in the wall.  I've also added jacks to
upstairs rooms with the wall plates.  This requires access to the basement
or attic, and lots of measuring to make sure that the hole you drill comes
out inside the wall instead of the floor/ceiling.  You will also need a
drywall knife and the plastic pop-in wall boxes that David mentioned.

It kind of makes wireless look a lot better, doesn't it?  <g>

Dave Parnin
--
Nishikawa Standard Company
Topeka, IN  46571
daparnin@xxxxxxxxxxxxxx




 

                      Dan

                      <dan27649@xxxxxxx        To:       PC Technical
Discussion for iSeries Users            
                      om>                       <pctech@xxxxxxxxxxxx>

                      Sent by:                 cc:

                      pctech-bounces@mi        Subject:  [PCTECH] Cat 5
cable RJ-45 connection HELP!          
                      drange.com

 

 

                      11/01/2005 10:03

                      AM

                      Please respond to

                      PC Technical

                      Discussion for

                      iSeries Users

 





(Is PC-tech the best/only list to post this? Would midrange-l be an
appropriate spot as well?)

I am running a Cat5 cable in my house to a room for which I had to drill a
hole just big enough for the cable but not for the end connector. So, in my
infinite wisdom, I bought 40 feet of Cat5 and a box of 10 connectors, and
borrowed the RJ-45 crimper we have here in the office from way back when we
used to make our own.

So, I use the crimper to snip about a half inch from the cable jacket, and
wonder to myself "How in the h... heck am I supposed line these color-coded
wires up so that they miraculously land in their proper slots?" I found a
reference to color coding at http://www.aptcommunications.com/ncode.htm, so
I now understand the importance of getting these wires lined up correctly.
But getting them there... Where's the magnifying glass and the
micro-surgeon's touch?

Is there an easier / more reliable way to do this?

TIA, Dan
--
This is the PC Technical Discussion for iSeries Users (PcTech) mailing list
To post a message email: PcTech@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/pctech
or email: PcTech-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
 at http://archive.midrange.com/pctech.