× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



Looking at that first document:

There is no MgmtCtrl.properties file on my PC hard drive.

When it talks firewall, is it talking the Windows firewall on my PC? Or
the firewall to the outside world? My PC is on the LAN (duh).

I did this: CALL PGM(QSYS/QYPSCONFIG) PARM(QYPS_HOSTNAME '192.168.0.1')
followed by restarting Management Central. No joy. I right-click on New
Monitor and get the same error.

The 2nd and 3rd documents have to do with clusters and I don't even know
what clusters are. Except for that OTHER kind of cluster . . . :)





On Wed, Aug 19, 2015 at 1:03 PM, <rob@xxxxxxxxx> wrote:

Sometimes Google is not your friend. Sometimes it's just better to go to
ibm.com and search in their little search box.

http://www-01.ibm.com/support/docview.wss?uid=nas8N1010549
http://www-01.ibm.com/support/docview.wss?uid=nas8N1014324
http://www-01.ibm.com/support/docview.wss?uid=nas8N1015105

I think you are a single lpar shop, otherwise these may pertain:
http://www-01.ibm.com/support/docview.wss?uid=nas8N1011404
http://www-01.ibm.com/support/docview.wss?uid=nas8N1014845


Rob Berendt
--
IBM Certified System Administrator - IBM i 6.1
Group Dekko
Dept 1600
Mail to: 2505 Dekko Drive
Garrett, IN 46738
Ship to: Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com





From: Jeff Crosby <jlcrosby@xxxxxxxxxxxxxxxx>
To: Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>
Date: 08/19/2015 12:54 PM
Subject: Management Central message monitor setup
Sent by: "MIDRANGE-L" <midrange-l-bounces@xxxxxxxxxxxx>



We had an unanswered message in QSYSOPR late yesterday afternoon that
caused issues after hours and this morning. I'm looking at ways to
monitor
QSYSOPR. I googled and found instructions for setting up a message
monitor
in Management Central for QSYSOPR message queue.

I expanded Management Central/Monitors. When I right-click "Message" then
"New Monitor" it fails with the following in the joblog:


Additional Message Information



Message ID . . . . . . : CPFB92A

Date sent . . . . . . : 08/19/15 Time sent . . . . . . :
11:22:04


Message . . . . : Unexpected exception occurred during Management
Central
protocol.



Cause . . . . . : An unexpected protocol exception occurred on system

I5.DILGARDFOODS.COM.

Recovery . . . : If the problem persists, contact service.

followed by:

Additional Message Information



Message ID . . . . . . : CPFB96B

Date sent . . . . . . : 08/19/15 Time sent . . . . . . :
11:22:04


Message . . . . : Authentication failed for request from user JEFF on
system
JLCROSBY.



Cause . . . . . : The Management Central server on system

MYIBMI.MYCOMPANY.COM was not able to authenticate the request from
system
JLCROSBY using protocol 8192. The protocols are: 1024 and 8192 -

Profile/Password protocol, 512 - Kerberos protocol.

Recovery . . . : For protocol 1024 and 8192, profile and password

authentication is being used. Check previous messages for more
information.
Verify that the user profile exists on each system with the
appropriate

granted authorities and submit the request again. For protocol 512,

Kerberos authentication is being used. Check previous messages for
more

information. Verify that Kerberos is properly configured on both
systems
and submit the request again.



Googling CPFB92A results in few hits, one of which says

"The following IBM document may very easily have the answer to the
problem,
however it is restricted and you have to have PartnerWorld access to get
to
it. Why do they restrict documents like this? 29531900, Cannot Start
Monitors Because of Messages CPFB92A and CPFB96B"

I googled that document and found zilch.

Management Central server is running, though I don't remember ever using
it
much. System i 520, V7R1, pretty current on PTFs. I'm using my signon
(*ALLOBJ authority) in System i Navigator. QSECOFR is not disabled.

Suggestions? Should I change Management Central to use IP address instead
of MYIBMI.MYCOMPANY.COM?

Thanks.


--


Jeff Crosby
VP Information Systems
UniPro FoodService/Dilgard
P.O. Box 13369
Ft. Wayne, IN 46868-3369
260-422-7531
www.dilgardfoods.com

The opinions expressed are my own and not necessarily the opinion of my
company. Unless I say so.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.



--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.





As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.