Try using OPTION(*CNTRLD) DELAY(10). That seems to bring things down more
"peacefully"
Paul Nelson
Cell 708-670-6978
Office 409-267-4027
nelsonp@xxxxxxxxxxxxx
-----Original Message-----
From: MIDRANGE-L [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
Steinmetz, Paul
Sent: Wednesday, July 29, 2015 7:50 AM
To: 'Midrange Systems Technical Discussion'
Subject: Job taking long time to end - CPC1165
On our R&D LPAR, I was ending some subsystems for a maintenance refresh of
data.
Normally, ENDSBS SBS(INTERFACD1) OPTION(*IMMED) will end all jobs in the
subsystem in less than 10 seconds.
One job threw a CPC1165, followed by a CPC1166, took over 2 minutes to end.
I've never seen this behavior.
System values set at defaults.
I'm not sure increasing the system values would help.
Any thoughts from the group?
System value . . . . . : QENDJOBLMT
Description . . . . . : Time limit during immediate ending of a job
Seconds . . . . . . . : 120 30-3600
System value . . . . . : QPWRDWNLMT
Description . . . . . : Maximum time for PWRDWNSYS *IMMED
Seconds . . . . . . . : 900 0-32767
CPC1207 Completion 50 07/28/15 16:55:07.400361 QWTMMTRS
QSYS 0247 *EXT *N
From user . . . . . . . . . : QSYS
Thread . . . . : 00000001
Message . . . . : Subsystem ending
immediately.
CPC1165 Completion 50 07/28/15 16:55:07.813862 QWTMMTRS
QSYS 0771 *EXT *N
From user . . . . . . . . . : QSYS
Thread . . . . : 00000001
Message . . . . : SIGTERM signal sent
to job 472732/DEVD1/OBNORM01D.
Cause . . . . . : Job
472732/DEVD1/OBNORM01D is being ended immediately. The
job has a signal handling procedure
for the asynchronous signal SIGTERM. A
SIGTERM signal has been sent to the
job. A time limit of 120 seconds will be
used to ensure that the job ends.
CPC1166 Completion 50 07/28/15 16:57:08.378316 QWTMETMR
QSYS 01BC *EXT *N
From user . . . . . . . . . : QSYS
Thread . . . . : 00000001
Message . . . . : Time limit reached
for SIGTERM signal handler.
Cause . . . . . : Job
472732/DEVD1/OBNORM01D did not complete during the
time allowed. An immediate end job
request was issued by the system. The
time limit was 120 seconds. Recovery
. . . : If the time limit of 120
seconds is not enough time for the
SIGTERM signal handler to complete,
contact your system administrator to
increase the time allowed by the
QENDJOBLMT and QPWRDWNLMT system
values.
CPF1164 Completion 00 07/28/15 16:57:09.485652 QWTMCEOJ
QSYS 014A *EXT *N
Thread . . . . : 00000001
Message . . . . : Job
472732/DEVD1/OBNORM01D ended on 07/28/15 at 16:57:09;
18.756 seconds used; end code 50 .
Cause . . . . . : Job
472732/DEVD1/OBNORM01D completed on 07/28/15 at
16:57:09 after it used 18.756 seconds
processing unit time. The job had
ending code 50. The job ended after 1
routing steps with a secondary ending
code of 0. The job ending codes and
their meanings are as follows: 0 - The
job completed normally. 10 - The job
completed normally during controlled
Thank You
_____
Paul Steinmetz
IBM i Systems Administrator
Pencor Services, Inc.
462 Delaware Ave
Palmerton Pa 18071
610-826-9117 work
610-826-9188 fax
610-349-0913 cell
610-377-6012 home
psteinmetz@xxxxxxxxxx
http://www.pencor.com/
midrange.com
