On our R&D LPAR, I was ending some subsystems for a maintenance refresh of data.
Normally, ENDSBS SBS(INTERFACD1) OPTION(*IMMED) will end all jobs in the subsystem in less than 10 seconds.
One job threw a CPC1165, followed by a CPC1166, took over 2 minutes to end.
I've never seen this behavior.
System values set at defaults.
I'm not sure increasing the system values would help.
Any thoughts from the group?
System value . . . . . : QENDJOBLMT
Description . . . . . : Time limit during immediate ending of a job
Seconds . . . . . . . : 120 30-3600
System value . . . . . : QPWRDWNLMT
Description . . . . . : Maximum time for PWRDWNSYS *IMMED
Seconds . . . . . . . : 900 0-32767
CPC1207 Completion 50 07/28/15 16:55:07.400361 QWTMMTRS QSYS 0247 *EXT *N
From user . . . . . . . . . : QSYS
Thread . . . . : 00000001
Message . . . . : Subsystem ending immediately.
CPC1165 Completion 50 07/28/15 16:55:07.813862 QWTMMTRS QSYS 0771 *EXT *N
From user . . . . . . . . . : QSYS
Thread . . . . : 00000001
Message . . . . : SIGTERM signal sent to job 472732/DEVD1/OBNORM01D.
Cause . . . . . : Job 472732/DEVD1/OBNORM01D is being ended immediately. The
job has a signal handling procedure for the asynchronous signal SIGTERM. A
SIGTERM signal has been sent to the job. A time limit of 120 seconds will be
used to ensure that the job ends.
CPC1166 Completion 50 07/28/15 16:57:08.378316 QWTMETMR QSYS 01BC *EXT *N
From user . . . . . . . . . : QSYS
Thread . . . . : 00000001
Message . . . . : Time limit reached for SIGTERM signal handler.
Cause . . . . . : Job 472732/DEVD1/OBNORM01D did not complete during the
time allowed. An immediate end job request was issued by the system. The
time limit was 120 seconds. Recovery . . . : If the time limit of 120
seconds is not enough time for the SIGTERM signal handler to complete,
contact your system administrator to increase the time allowed by the
QENDJOBLMT and QPWRDWNLMT system values.
CPF1164 Completion 00 07/28/15 16:57:09.485652 QWTMCEOJ QSYS 014A *EXT *N
Thread . . . . : 00000001
Message . . . . : Job 472732/DEVD1/OBNORM01D ended on 07/28/15 at 16:57:09;
18.756 seconds used; end code 50 .
Cause . . . . . : Job 472732/DEVD1/OBNORM01D completed on 07/28/15 at
16:57:09 after it used 18.756 seconds processing unit time. The job had
ending code 50. The job ended after 1 routing steps with a secondary ending
code of 0. The job ending codes and their meanings are as follows: 0 - The
job completed normally. 10 - The job completed normally during controlled
Thank You
_____
Paul Steinmetz
IBM i Systems Administrator
Pencor Services, Inc.
462 Delaware Ave
Palmerton Pa 18071
610-826-9117 work
610-826-9188 fax
610-349-0913 cell
610-377-6012 home
psteinmetz@xxxxxxxxxx
http://www.pencor.com/
midrange.com
