Re: Attaching Hitachi HUS VM to IBM i LPARs -- MIDRANGE-L

No, you do it this way:

Hitachi LUNS = 0 1 2 3 4

Dual VIOS redundantly connected to HITACHI sees LUNS 0 1 2 3 4 (important
that the hdisks be configured as the manual says for Dual Vios, otherwise
failover and load balancing fail due to LUN lock).

Dual VIOS present the same disks to each partition via vSCSI adapters.

IBM i sees both adapters and sees the 2 paths to each disk.

That's how i have it set up on a client, and that was how i read the
manual, but let's wait for Sue or the Dr to be sure. Also, i'm not sure why
they say IBM i 7.1, last i read it was IBM i 6.1.1 or later.

Best Regards,

Roberto

On Wed, Jul 16, 2014 at 1:16 PM, Mitchell, Dana <dmitche@xxxxxxxxxx> wrote:

There was an update to this doc dated 05/14. Probably hasn't changed much
since John got his copy. I'm curious though, it says:

5) Dual VIOS with IBM"i" for v7.1.0 and above & VIOS 2.2 and above is
supported.
6) Virtual SCSI or vSCSI virtualization is supported.
7) We do not support vFC/NPIV with IBM"i" clients due to 520 block size.

So without NPIV, Dual VIOS would just let IBM i mirror two (sets) of vSCSI
disks?

Dana

-----Original Message-----
From: MIDRANGE-L [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
Mitchell, Dana
Sent: Tuesday, July 15, 2014 10:23 AM
To: Midrange Systems Technical Discussion
Subject: RE: Attaching Hitachi HUS VM to IBM i LPARs

Thanks John, that was my suspicion. I'll see if there's an update to that
doc...

Dana

-----Original Message-----
From: MIDRANGE-L [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
John.BresinaJr
Sent: Tuesday, July 15, 2014 9:32 AM
To: Midrange Systems Technical Discussion
Subject: RE: Attaching Hitachi HUS VM to IBM i LPARs

I did setup our IBM I servers to use Hitachi storage and prior to setup I
contacted them in 2011 to make sure I could use their storage arrays. They
sent me a document titled: IBM I Support Document 03_25_11.pdf.
In that document it said: We do not support vFC/NPIV with IBM i clients
due to 520 block size. You may have to contact Hitachi to find out of that
has changed in the past 3 years. I ended up setting up vSCSI as vSCSI
virtualization is supported by Hitachi with a VIOS.

John

John Bresina Jr | Sr Engineer | TTS Server Tech - Tandem/System
i/Mainframe | Target | Mailstop: NCE-0706 | 7000 Target Parkway North |
Brooklyn Park, MN 55445| 612 304 3665 (ph)

-----Original Message-----
From: MIDRANGE-L [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
Mitchell, Dana
Sent: Tuesday, July 15, 2014 8:09 AM
To: Midrange Systems Technical Discussion
Subject: Attaching Hitachi HUS VM to IBM i LPARs

Our company currently uses Hitachi HUS VM for storage for AIX LPARs. Now
we are looking at a new P8 machine(s) to replace a boxes that houses a
total of 10 IBM LPARs and the question came up, why don't we use storage
in the Hitachi subsystem for this new box. The official Hitachi line is
that HUS VM supports storage as presented to VIOS, but I can't find any
confirmation that it supports NPIV to LUNs to IBM i LPARs. In addition,
since the Hitachi subsystem here already has replication set up to our DR
site, we could discontinue using iTERA for replication. Has anyone here
used Hitachi storage to attach to IBM i and/or with replication? Any
experience to share?

Thanks
Dana

Attention: This electronic document and associated attachments (if any)
may contain confidential information of the sender (SHAZAM Network) and is
intended solely for use by the addressee(s). Review by unintended
individuals is prohibited. If you are not the intended recipient: (i) do
not read, transmit, copy, disclose, store, or utilize this communication in
any manner; (ii) please reply to the sender immediately, state that you
received it in error and permanently delete this message and any
attachment(s) from your computer and destroy the material in its entirety
if in hard copy format. If you are the intended recipient, please use
discretion in any email reply to ensure that you do not send confidential
information as we cannot secure it through this medium. By responding to us
through internet e-mail, you agree to hold SHAZAM, Inc. and all affiliated
companies harmless for any unintentional dissemination of information
contained in your message. Thank you. (2)
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.

Attention: This electronic document and associated attachments (if any)
may contain confidential information of the sender (SHAZAM Network) and is
intended solely for use by the addressee(s). Review by unintended
individuals is prohibited. If you are not the intended recipient: (i) do
not read, transmit, copy, disclose, store, or utilize this communication in
any manner; (ii) please reply to the sender immediately, state that you
received it in error and permanently delete this message and any
attachment(s) from your computer and destroy the material in its entirety
if in hard copy format. If you are the intended recipient, please use
discretion in any email reply to ensure that you do not send confidential
information as we cannot secure it through this medium. By responding to us
through internet e-mail, you agree to hold SHAZAM, Inc. and all affiliated
companies harmless for any unintentional dissemination of information
contained in your message. Thank you. (2)
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.

Attention: This electronic document and associated attachments (if any)
may contain confidential information of the sender (SHAZAM Network) and is
intended solely for use by the addressee(s). Review by unintended
individuals is prohibited. If you are not the intended recipient: (i) do
not read, transmit, copy, disclose, store, or utilize this communication in
any manner; (ii) please reply to the sender immediately, state that you
received it in error and permanently delete this message and any
attachment(s) from your computer and destroy the material in its entirety
if in hard copy format. If you are the intended recipient, please use
discretion in any email reply to ensure that you do not send confidential
information as we cannot secure it through this medium. By responding to us
through internet e-mail, you agree to hold SHAZAM, Inc. and all affiliated
companies harmless for any unintentional dissemination of information
contained in your message. Thank you. (2)
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.