Re: Forms printing

[Michael Ryan <michaelrtr@xxxxxxxxx>]

Here are the steps I use:

1. Create/modify MS Word document.
	C:\RTR\somedir\somedoc.doc

2. Print individual pages as different overlays using the AFP 300 driver.
	Use naming convention of YYMMDDn, where n is the page number.

3. Upload .prn files to \\youri\Overlays IFS directory
	Mapped drive or binary FTP

4. Copy from IFS directory to OVERLAYS file.
	CPYFRMSTMF FROMSTMF('/overlays/t0805151.prn')

TOMBR('/qsys.lib/mylib.lib/overlays.file/t0805151.mbr')
                   CVTDTA(*NONE)
                   ENDLINFMT(*FIXED)
                   TABEXPN(*NO)

5. Create overlay.
	CRTOVL OVL(mylib/T0805151) FILE(OVERLAYS)

On Thu, Mar 3, 2011 at 7:24 AM, jmmckee <jmmckee@xxxxxxxxxxxxxx> wrote:
> Fortunately, this is not a high volume form.  Maybe a few hundred a day, but spread out over maybe 60 printers, none are IPDS.
>
> Bad news is I finally got an opportunity to examine the form.  Around 120 fields, many boxes with labels.  Spacing, both vertical and horizontal, seems to vary.  Looked like 5 lines/inch at one point and something between 8 and 12 cpi.  I had hoped to use an overlay of the original Lexmark form for both sides.  Back side is still likely, as it has two fields and no boxes - just lots of canned text.
>
> I'm not clear on the initial steps of overlay generation.  The Redbook says to load the AFP printer driver from Client Access.  When I try, I get a message stating it is already loaded, but I don't see the same drivers as listed in the Redbook.  That might be because there was a glitch and I installed from the web the Infoprint driver.  The CA install share was mysteriously unavailable.  Maybe I need to uninstall the Infoprint driver and try installing from the CA share again.  We are on v5r4, and stalled, pending removal of the system in a few years (master planning of a corporate office - trash everything).
>
> So, I san the original document into a JPEG file, then print it using any Windows application to a file using AFP driver.  Upload file to IBM i, CRTOVL.  Is this correct?
>
> John McKee
> -----Original message-----
> From: Charles Wilt charles.wilt@xxxxxxxxx
> Date: Wed, 02 Mar 2011 09:40:46 -0600
> To: Midrange Systems Technical Discussion midrange-l@xxxxxxxxxxxx
> Subject: Re: Forms printing
>
> > Note that there are some benefits to using an AFP capable IPDS printer...
> >
> > With HPT, the overlay (and fonts) are sent as part of the spool data
> > stream for each spool file.
> >
> > With IPDS, the overlay (and fonts) are sent as needed and can be
> > cached on the printer.
> >
> > Also, my impression is the IPDS data stream is overall a bit more
> > reliable and easier to configure than HPT.
> >
> > My preference and IBM's recommendation, is for IPDS printers for
> > critical and/or high volume printing such as invoices.
> >
> > Charles
> >
> > On Wed, Mar 2, 2011 at 7:22 AM, Michael Ryan <michaelrtr@xxxxxxxxx> wrote:
> > > I usually use the AFP 300 printer driver.
> > >
> > > I generate the forms using an overlay, and HPT to a laser printer.
> > > Need to specify *AFPDS for the printer file, but just a regular laser
> > > printer.
> > >
> > > On Tue, Mar 1, 2011 at 10:44 PM, jmmckee <jmmckee@xxxxxxxxxxxxxx> wrote:
> > > > The redbook, http://www.redbooks.ibm.com/redbooks/pdfs/sg242160.pdf is easy enough to read.  But, I have a couple of questions:
> > > >
> > > > 1) I have an existing blank form.  I am assuming that the form would need to be scanned and then printed to a file using the AFP printer.  Which one would I use?
> > > >
> > > > 2) Is an IPDS printer required, or would an AFPDS printer file work when directed to a laser printer.  The form has boxes and text with different fonts.
> > > >
> > > >
> > > > Currently, forms are being generated by a forms chip inside a Lexmark printer.  Would really be nice to not be tied to a specific printer model, which is no longer manufactured.
> > > >
> > > >
> > > > John McKee
> > --
> > This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
> > To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> > To subscribe, unsubscribe, or change list options,
> > visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> > or email: MIDRANGE-L-request@xxxxxxxxxxxx
> > Before posting, please take a moment to review the archives
> > at http://archive.midrange.com/midrange-l.
> --
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.