Re: Problems transferring with i Nav between V7R1 and V5R4

Is the save file in a library that migh not be in your library list, again
just guessing. Wondering if behind the scenes QUSER is doing something with
the move process.

On Wed, Jan 12, 2011 at 3:37 PM, Joe Pluta<joepluta@xxxxxxxxxxxxxxxxx>wrote:

After upgrading to V7R1 of iNav, I unhappily report the same result. I
can move objects from the V5R4 machine to the V7R1 machine, but not the
other way. On the V5R4 machine I see a QHST log entry saying that the
unpack failed because of incompatible SAVF release.

Reminds me of the way we could move data from the S/38 to the AS/400 but
not vice versa when we were converting BPCS to the AS/400. Chuck Myaard
said we would have to "wumpus up a way" to move the data, and we did -
and the WRKWUMPUS command was born. :)

Joe

Joe, what version of ISERIES Access.

On Wed, Jan 12, 2011 at 8:31 AM, Joe Pluta<joepluta@xxxxxxxxxxxxxxxxx

wrote:

We have a brand new V7R1 partition and I'm trying to send a library

from

the V7R1 partition to the older V5R4 partition using iSeries Navigator
V5R4. It fails, and the message I get in the joblog is this:

CPF9812 Escape 40 01/12/11 06:57:11.456944
QSRLIBS1 QSYS *STMT QZRCSRVS QSYS *STMT
From user . . . . . . . . . :
JPLUTA
From module . . . . . . . . :
QSRS1MED
From procedure . . . . . . :
qsrSendMediaMessages
Statement . . . . . . . . . :

32

To module . . . . . . . . . :
QZRCRMTC
To procedure . . . . . . . :
RunCommand
Statement . . . . . . . . . :

49

Message . . . . : File @@5123

in

library QYDSOBJ0 not found.
Cause . . . . . : The file

name

or the library name is not correct. If the
library name was not

specified,

the file may be in a library that is not
contained in the library list.
Recovery . . . : Correct the file or
library name, or add the

library

name to the library list. Then try the
request again.


The library being sent is @@5123. Not sure what QYDSOBJ0 is, probably

a

temporary library. In QHST, I see a message that says a library cannot
be displayed or restored because it's the wrong level.

Cause . . . . . : The file was saved from a more recent release of

the

operating system or the CD-ROM was not created correctly. The
operation was
requested for save file QYDS657270 in library QRPLOBJ.

I suspect that is the attempt to restore the save file that iNav sent

over.

As a side point, when I manually create a save file and FTP it over, it
works fine. Any ideas?

Joe
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing

list

To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.