RE: Changed our IP address now SMTP is broken

OK, found the solutiuon:

We had to remove the SMTP List Entries for the old ip
address and add them back with the new IP address

RMVSMTPLE TYPE(*SVRBIND) INTNETADR('192.168.1.50')
ADDSMTPLE TYPE(*SVRBIND) INTNETADR('192.168.2.50')

RMVSMTPLE TYPE(*CLTBIND) INTNETADR('192.168.1.50')
ADDSMTPLE TYPE(*CLTBIND) INTNETADR('192.168.2.50')

Thanks for all that offered suggestions

John



-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
Shannon ODonnell
Sent: Thursday, August 02, 2007 9:31 AM
To: 'Midrange Systems Technical Discussion'
Subject: RE: Changed our IP address now SMTP is broken

Sounds like something else on your network is already using
that IP address
if you're getting a bind() error.



-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Allen
Sent: Thursday, August 02, 2007 8:13 AM
To: MIDRANGE-L@xxxxxxxxxxxx
Subject: Changed our IP address now SMTP is broken

While setting up VPN on our network we had to change the IP
address of our AS400 (V5R1) from 192.168.1.50 to
192.168.2.50



Everything appears to be back up and working (Users can log
on, map drives etc) except for SMTP

SMTP will start up (jobs QTSMTPBRCL QTSMTPBRSR QTSMTPCLTD
QTSMTPSRVD) they stay running for about 5 minutes



Then they end with the following in the joblog:

TCP206E Diagnostic 40 08/02/07 08:39:56
QTMSCLCD QTCP *STMT QTMSCLCD QTCP

From module . . . . . .
. . : QTMSCLUT

From procedure . . . .
. . : PostTCP206E__FiPc

Statement . . . . . . .
. . : 625

To module . . . . . . .
. . : QTMSCLCD

To procedure . . . . .
. . : main

Statement . . . . . . .
. . : 275

Message . . . . :
SMTP received an error from a sockets function.

Cause . . . . . :
Probable causes are: -- network problem -- remote host

problem Technical
description . . . . . . . . : SMTP received errno 3421

from sockets function
BIND(). To see the meaning of the errno, enter command

DSPMSGD
RANGE(CPEXXXX), where XXXX is the four digit errno value.




TCP2081 Diagnostic 20 08/02/07 08:39:56
QTMSUTL QTCP *STMT QTMSCLCD QTCP
*STMT

From module . . . . .
. . . : QTMSUTIL


From procedure . . .
. . . : qtms_IssueMessage


Statement . . . . . .
. . . : 1747


To module . . . . . .
. . . : QTMSCLCD


To procedure . . . .
. . . : main


Statement . . . . . .
. . . : 276


Message . . . . :
SMTP unable to bind to Internet Protocol interface


192.168.1.50.


Recovery . . . :
Check the status of Internet Protocol interface


192.168.1.50 with
the command NETSTAT *IFC, and start if necessary, or


correct problems.




When I run the command NETSTAT *IFC is shows our new IP
address 192.168.2.50 not the 192.168.1.50 that is shown in
the message above from the joblog

So something somewhere still has our old IP address



Any ideas would be greatly appreciated



John