× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



I'm not so sure that is true. With the model 200 and model 400, the address
of the drive is determine by a jumper or two on the actual drive itself.
The jumper pinouts are on the side of the metal on the inside of the cover.
I think as long as the drive is on the same bus, it doesn't matter where in
the chain it is.
cjg


Carl J. Galgano
EDI Consulting Services, Inc.
770-422-2995
www.ediconsulting.com

600 Kennesaw Avenue
Suite 400
Marietta, GA 30060

-----Original Message-----
From: midrange-l-bounces+cgalgano2=ediconsulting.com@xxxxxxxxxxxx
[mailto:midrange-l-bounces+cgalgano2=ediconsulting.com@xxxxxxxxxxxx] On
Behalf Of Steve Landess
Sent: Saturday, June 16, 2007 4:05 PM
To: Midrange Systems Technical Discussion
Subject: Re: Model 200 - One More Time

Once you get the drives out, remember to tag each one as to which bay they
came from...

----- Original Message -----
From: "Larry Bolhuis" <lbolhuis@xxxxxxxxxx>
To: "Midrange Systems Technical Discussion" <midrange-l@xxxxxxxxxxxx>
Sent: Friday, June 15, 2007 10:47 PM
Subject: Re: Model 200 - One More Time


Hammer? Crowbar? BFH? Next thing they'll say "Heat Wrench!" (Acetylene
Torch for the unknowing). Neanderthals!

Opening it up isn't hard. First git yerself a 7MM socket and chuck it up
in yer drill/driver and lock the driver into reverse. Then pull the
front cover straight off. Around back loosen the screw at the top
center. Slide it back and lift it up. Then remove the two screws at the
top of each plastic side cover and they will fall off. From here on it's
a simple matter of removing every freekin screw you can find. The sides
will fall off once the screws are off. Up to four drives will be on the
left and up to eight on the right. In each case you'll need to pull off
the power and data cables then the drives will simply pull out (though
they are fairly stiff.)

Good Luck!

- L

Matt Gross wrote:
The box is toast, but I'll try one more thing. Does anyone know how I
can open it up to get at the drive(s), power supply, etc.

Thanks,

Matt

PS - this system doesn't run any company. This was a giveaway I
sometimes use if a small project comes up.


--

Larry Bolhuis IBM Certified Advanced Technical Expert
- System i Solutions
Vice President IBM Certified Systems Expert:
Arbor Solutions, Inc. System i Technical Design and
Implementation V5R4
1345 Monroe NW Suite 259 eServer i5 iSeries LPAR Technical
Solutions, V5R3
Grand Rapids, MI 49505 IBM Certified Specialist
System i Integration with BladeCenter
and System x V1
(616) 451-2500 System i IT Simplification: Linux
Technical V5R4
(616) 451-2571 - Fax iSeries System Administrator for
OS/400 V5R3
(616) 260-4746 - Cell

If you can read this, thank a teacher....and since it's in English,
thank a soldier.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.




As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.