Re: SOLVED - No signon screen

[MWalter@xxxxxxxxxxxxxxx]

Cool

Thanks,

Mark

Mark D. Walter
Senior Programmer/Analyst
CCX, Inc.
mwalter@xxxxxxxxxx
http://www.ccxinc.com


                                                                           
             Pete Helgren                                                  
             <Pete@xxxxxxxxxx>                                             
             Sent by:                                                   To 
             midrange-l-bounce         Midrange Systems Technical          
             s@xxxxxxxxxxxx            Discussion                          
                                       <midrange-l@xxxxxxxxxxxx>           
                                                                        cc 
             04/19/2005 05:20                                              
             PM                                                    Subject 
                                       Re: SOLVED - No signon screen       
                                                                           
             Please respond to                                             
             Midrange Systems                                              
                 Technical                                                 
                Discussion                                                 
             <midrange-l@midra                                             
                 nge.com>                                                  
                                                                           
                                                                           




Chris, Mark, Rob and Scott.

A few more clues and I think I have the answer.

C09 has the 266C in it.  Based on what Chris said, it should have a 4
port brick attached.  It does NOT.  In fact, I don't even HAVE a 4 port
brick.  I think I have one on my 270 at home though....

SO !

Looks like I need to have the 4 port brick attached to the 266C and
based on Rob directions, it shows that as CTL01 and that should give me
a console (won't know until I get a 4 port brick attached).

Part Deux is:

CTL02, then, has the current terminal in place, yet, it didn't give me a
signon.  Working the hunch that the QINTERXXX subsystem was a clue, I
did use WRKSBSD QINTER* and DID find a QINTER subsystem.  It has the
*CONS entry in it and *ALL. But, it wasn't started.  I started it and it
DID  give me a signon screen.  I has assumed, wrongly, that the
QINTER001 and QINTER002 subsystems were all that were needed.  For
telnet, yes, but for DSP020000 I needed to have QINTER running.

So that is it then.  Before I scratch this thing I need the 4 port brick
and then verify that I get a console, at that point I should be able to
do what I need to do.

Thanks all for the help.

Pete


Ingvaldson, Scott wrote:

>What is in slot C09?
>
>-----Original Message-----
>date: Tue, 19 Apr 2005 12:38:31 -0600
>from: Pete Helgren <Pete@xxxxxxxxxx>
>subject: Re: No signon screen
>
>No. No Ops Console. This system always had a Twinax console.
>
>But, I am beginning to think that there WAS another twinax controller at
>one time.
>
>Here is what I am seeing:
>
>CTL01 is a 266C device type (not sure what that is exactly)
>CTL02 is a 2722 device type.
>
>The QCTLSBSD is QCTL.  QCTL is active.  There is a QCTL controller
>defined as a 266C device although it is varied off.  If you try to vary
>it on it tells you that the resource is already in use (presumably by
>CTL01 which uses the same resource).
>
>When I delete the terminal device description on CTL02 (the only device
>configured on it), it autoconfigs as DSP020000 which tells me that it is
>on CTL02 (true) and has address 0 (true) on port 0 (true).  Even if I
>didn't want this as a console, shouldn't it still give me a signon
>screen?
>
>There is only one connector at the back of the 720 that will connect to
>the "brick".
>
>I just re-checked that the cable and terminal are OK by taking the
>terminal and cable off of our Model 800 and putting it on the 720.  No
>luck.
>
>I suspect that it has something to do with the fact that the Twinax
>controller is CTL02 and probably something to do with the multiple
>QINTER subsystems but I can't quite pull it all together.
>
>Pete
>
>
>
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.