RE: IPL Error -- MIDRANGE-L

Rob,
One thing I do notice is that when the console comes up it shows the
subsystem as qinter and the device as dsp03, I know that those are
wrong, any suggestions on how to change it to where it shold be?


-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of rob@xxxxxxxxx
Sent: Friday, April 01, 2005 2:22 PM
To: Midrange Systems Technical Discussion
Subject: Re: IPL Error


It's a rather funny device and only comes active when in certain service

situations.  Everyone's QCONSOLE is set to online(*no).

Rob Berendt
-- 
Group Dekko Services, LLC
Dept 01.073
PO Box 2000
Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com





"Joe Lee" <LeeJD@xxxxxx> 
Sent by: midrange-l-bounces@xxxxxxxxxxxx
04/01/2005 03:13 PM
Please respond to
Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>


To
<midrange-l@xxxxxxxxxxxx>
cc

Subject
Re: IPL Error






This is probably a stupid question, but does "Online at IPL *NO" mean
that 
the terminal is not on during IPL? And if so wouldn't that prevent it
from 
being detected?

Joe Lee

>>> dpalme@xxxxxxxxxxx 04/01/2005 11:17:44 >>>
Here is the details from the devd

 Device description . . . . . . . . :   QCONSOLE 
 Option . . . . . . . . . . . . . . :   *BASIC 
 Category of device . . . . . . . . :   *DSP 
 
 Device class . . . . . . . . . . . :   *LCL 
 Device type  . . . . . . . . . . . :   3487 
 Device model . . . . . . . . . . . :   HC 
 Port number  . . . . . . . . . . . :   0 
 Switch setting . . . . . . . . . . :   0 
 Shared session number  . . . . . . :   0 
 Online at IPL  . . . . . . . . . . :   *NO 
 Attached controller  . . . . . . . :   QCTL 
 Keyboard language type . . . . . . :   USB 
 Character identifier . . . . . . . :   *KBDTYPE 
 Allow blinking cursor  . . . . . . :   *YES 
 Print device . . . . . . . . . . . :   *SYSVAL 

>From what I can tell everything looks fine.

On Fri, 1 Apr 2005 09:37:05 -0500, Al Barsa wrote
> Two things:
> 
> 1.    Check that the console is at twinax controller 0, port 0,
>  switch setting 0.
> 2.    Double check, get the name of the console from the job name, 
> and do a DSPSYSVAL QCONSOLE and make sure it matches.
> 
> Al
> 
> Al Barsa, Jr.
> Barsa Consulting Group, LLC
> 
> 400>390
> 
> "i" comes before "p", "x" and "z"
> e gads
> 
> Our system's had more names than Elizabeth Taylor!
> 
> 914-251-1234
> 914-251-9406 fax
> 
> http://www.barsaconsulting.com
> http://www.taatool.com 
> http://www.as400connection.com 
> 
>              dpalme@xxxxxxxxxx 
>                    m 
>                          Sent by: 
>                To              midrange-l-bounce         Midrange 
> Systems Technical                       s@xxxxxxxxxxxx 
>  Discussion 
>        <midrange-l@xxxxxxxxxxxx> 
>                                               cc
>  03/31/2005 10:47 
>        PM                                                    Subject 
>                                        Re: IPL Error
> 
>              Please respond to 
>                    Midrange Systems 
>                              Technical 
>                                   Discussion 
>                                      <midrange-l@midra 
>                                                nge.com>
> 
> I was working from the console, our console is connected via twinax 
> and with a normal IPL it loads fine, and we can log in from the 
> console with no problem, perform normal everyday routines, it is only 
> when attempting a BM that it fails.
> 
> The console is connected and powered on
> 
> On Thu, 31 Mar 2005 19:40:51 -0800, Keith Carpenter wrote
> > The whole point of a manual IPL is to use the console to do system 
> > maintenance functions like upgrade the OS, apply PTFs, or run DST 
> > (dedicated mode service tools).
> >
> > A Normal IPL will start the OS with or without a console.  Hence no 
> > need to generate an error if the console is not connected or powered

> > off.
> >
> > Do you have a console ?
> > Is it connected and powered on ?
> >
> > I'm guessing you've not used a console before.
> > Your system (170) is configured to use either a twinax or ascii type

> > of console.  The type is is determined by the which cards are 
> > installed and the slots they are in.  There will be a special serial

> > cable for the ascii console.  Twinax (looks like a large 2 pin coax)

> > uses a dedicated 5250 terminal.
> >
> > Your system (probably recently purchased), should have come with 
> > some cables for either twinax or an ascii console.
> >
> > Keith
> >
> > D.W. wrote:
> > > I am trying to do a manual IPL and I am getting an error message 
> > > A6005008.  I did a look up on google and it appears that its
> complaining
> > > about not finding the console, but when I do a normal IPL it loads
with
> > > no problems.
> > >
> > > Suggestions? Ideas? I need to fix a system password issue and I am
down
> > > to about five days, and this is really starting to get irritating.
> > >


-- 
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing 
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.


-- 
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.