× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



Jan -

Read info APAR II13365 - SOFTWARE REQUIRED: 800, 810, 825, 870, 890
http://www-912.ibm.com/n_dir/nas4apar.nsf/0c42ed4609a123d486256c1b004c4ea7/9
4a6a270552366b286256c01003c9105?OpenDocument&Highlight=2,810

Specifically, you need to verify the level of LIC on your source system
(Section 1 - 1.a.)
DSPPTF LICPGM(5722999) SELECT(RE02343)
DSPPTF LICPGM(5722999) SELECT(RE03098)

If you are not at the correct level you will need to slip the LIC on your
source system before migrating to the 810.

If you have a 2757 PCI-X Ultra RAID Disk Controller on your 810 you will not
be able to see any of the drives under it until after the PTFed LIC code is
installed, the base LIC is not enough.  Our CE and I wasted about 4 hours
trying to figure out why the drives wouldn't show up before finishing the
restore and finding that they had magically appeared!

Regards,

Scott Ingvaldson
AS/400 System Administrator
GuideOne Insurance Group

-----Original Message-----
date: Thu, 11 Dec 2003 16:41:21 +0100
from: Jan.Rockstedt@xxxxxxxxxxxx
subject: Ang: Re: Restore 21 to a new Iseries

Hi Oliver !

Same version/release on both as/400.
No op-console.

Mvh / Regards Jan Rockstedt
HSB Syd IT
Spangatan 37B, 2:a van.
211 53 Malmo Sweden
Phone: +46-40 - 668 07 45
Fax: +46-40-668 07 55
www.sydit.hsb.se




oliver.wenzel@xxxxxxxxxxxxxxxxxxxxxxx
Sänt av: midrange-l-bounces@xxxxxxxxxxxx
2003-12-11 16:04
Sänd svar till Midrange Systems Technical Discussion
 
        Till:   Midrange Systems Technical Discussion 
<midrange-l@xxxxxxxxxxxx>
        Kopia: 
        Ärende: Re: Restore 21 to a new Iseries
Hi Jan,


>Soon is our S30 scrap iron.
>We have got a new 810 now. :-)
>Could someone point to any document how to run a restore 21 to a new 
>Iseries ?
>Or suggest any recomendation ?

We just switched from our 820 to our new 810 (basically a scratch reload).

As the hardware will not be the same, you'll have to check your device 
descriptions 
and connect them to the right controllers.

Do you have a twinax or OpsConsole? Make sure the Opsconsole is on the 
correct release
version. Also, be prepared to fight with OpsConsole cabling!

Whe we did the V5R2 upgrade of our 820, suddenly it wanted the OpsConsole 
cable in another
slot!

What release is your S30? It would be best if its the same as on the new 
810.

Regards,

Oliver
   
This message and accompanying documents are covered by the Electronic
Communications Privacy Act, 18 U.S.C. §§ 2510-2521, and contains information
intended for the specified individual(s) only. This information is
confidential. If you are not the intended recipient or an agent responsible
for delivering it to the intended recipient, you are hereby notified that
you have received this document in error and that any review, dissemination,
copying, or the taking of any action based on the contents of this
information is strictly prohibited. If you have received this communication
in error, please notify us immediately by e-mail, and delete the original
message.


As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.