CWBDB0058

Update on my file transfer problem.  After a couple days of file transfers 
working then not working then working again, I went to my client on Tuesday and 
found that suddenly people using client access could not connect.  Some were 
connected but if they disconnected, they could not re-connect.  Fortunately for 
the emails below, I checked QUSER and the max storage was indeed at 3196.  I 
changed it to *NOMAX and everything started working again.  Users could connect 
and file transfers worked!!!!!!  Thanks All!

        The point about checking that QUSER has MAXSTG(*NOMAX) is a good one.  
A 
        long time ago in a cornfield far far away, IBM used to ship AS/400 
systems 
        with MAXSTG(3176) for QUSER, and if these systems have been upgraded 
over 
        the years this may not have been changed.
        
        There are also some V5R2 PTF's that may help - SI08923, SI08871 & 
MF30604.
        Also check this link for TCP/IP stack PTF's:
        
http://www-1.ibm.com/support/docview.wss?uid=nas1d890cb0927aa56ad86256a3100633d95&rs=110
        
        Also, a less drastic solution than an IPL or ENDTCP *IMMED and STRTCP 
if 
        this problem occurs and nothing else seems to be helping:
        1) ENDHOSTSVR ALL
        2) DLTUSRSPC QUSRSYS/QYSMSVRE
        3) STRHOSTSVR *ALL
        
        ...Neil
        
        Philipp Rusch <Philipp.Rusch@xxxxxxxxxxxx> 
        
        I've had this type of error when the staff restored some libs after 
        upgrade without excluding
        QGPL and QUSRSYS. Afterwards nearly all TCPIP "prestarted jobs" seemed 
to 
        start and
        then stopped immediately after. I reinstalled option 12 of SS1 and 
        TC1-licpgm, and  it worked
        again, using CA Express V4R4, V4R5 and V5R2, no difference.
        If having problems with CAWIN connections, always check on QUSER 
profile, 
        max storage
        should be *NOMAX, look if it is not *DISABLED and refresh the password.
        
        HTH, Philipp Rusch
        
        "Smith, Dave" schrieb:
        
        > HELP!
        >
        >
        >
        > I have a client and their iSeries access data transfer quit working 
        today (it was working this morning but now its not.)   The error I am 
        getting is: CWBDB0058 Unable to start database server due to 
        communications error.
        >
        >
        >
        > Their system was upgraded to V5R2 last week but they have done 
transfers 
        since.  I've gone through STRPJ on QZDAINIT now in library QSYS (says 
        itÃÃÃs already started).   I've done a STRHOSTSVR *ALL and IÃÃÃve 
run 
        CWBPING which gives me a CWBCO1008 - Unable to connect to server 
        application Data Access, Returned 8006.   I also got the same thing on 
        application Network Print.  I ended the PJ and restarted it and even 
had 
        the luxury of being able to IPL the system (No comments please)   I get 
        the same error on all PCÃÃÃs that attempt an iseries access 
transfer.   I 
        canÃÃÃt find any error messages via the green screen side.  iSeries 
        Navigator says the database server is running, IÃÃÃm not seeing any 
other 
        error messages and everything else seems to be working.
        
        >
        >
        > David Smith