Re: send mail

["Bill Meecham" <bmeecham@xxxxxxxxxxxxxxxxxxxx>]

Try:   ENDMSF  and then   STRMSF *CLEAR


>
> Hi read all your mails about SNDDST and I followed instructions in the
> archives and on a website describing the setup of the smtp mailgateway.
> The only thing I get is a message at qsysopr saying:
>
> Bericht . . . . :   Job 284308/QMSF/QMSF stopped processing MSF message.
> Cause . . . . . :   Exit point program QTMSFWD in library QTCP for exit
> point
>   QIBM_QZMFMSF_MSG_FWD has detected a condition with message ID
>   44K70520101091806360000000004. The message indicates that processing
> should
>   be ended. The MSF message will be processed again the next time the
Start
>   Mail Server Framework (STRMSF) command is used.
> Recovery  . . . :   Determine why the exit point program indicated that
>   processing for a message is to be ended. There may be messages listed in
> the
>   job log that caused the exit point program to fail. Correct the error
and
>   use the End Mail Server Framework (ENDMSF) command to end all MSF jobs.
> Then
>   use the Start Mail Server Framework (STRMSF) command to start message
>   processing again
>
> And also:
>
> Bericht . . . . :   Bridge server job not contacted to begin sending.
> Cause . . . . . :   The extended bridge transform job could not contact
the
>   bridge server job.  This job is needed to send distributions to the
> target
>   system as part of the extended bridge function.
> Recovery  . . . :   Use the Work with Job (WRKJOB) command for job
> QTSMTPBRCL
>   to find the bridge server job log and determine what error ended the job
> or
>   is preventing it from responding.  Correct the error and start the
sender
>   again.
>
>
> Any ideas what is wrong ?
> Greetings,
> Bart
>
>
> ----- Original Message -----
> From: "Bart Verweijen" <bart.verweijen@advalvas.be>
> To: "Midrange L" <MIDRANGE-L@midrange.com>
> Sent: Tuesday, January 09, 2001 2:40 PM
> Subject: send mail
>
>
> > Hi all,
> >
> > Is there a way to send a smtp message (e-mail) to a smtpserver through
> the
> > commandline or through a cl program ?
> >
> > I want a program to send an email everytime something occurs...
> >
> > Thanks for your time,
> > Bart
> >
>
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
> MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
> david@midrange.com
> +---
>
>
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
david@midrange.com
> +---

+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---