RE: Table saw shake

Try CFGSAW option 12.  Make sure the saw is defined as *TABLE with a
graphite blade. 

Then take option 10 and make sure there is any entry for Medium Density
Fiberboard (*MDF), High Density FiberBoard (*HDF), Pressure treated Lumber
(*PRSTRT) and any other wood that you may use.  (F4 to prompt.. help text is
pretty good too.) 

Then do,
STRSAWSVR SAW(*TABLE) PARM('shake 0' 'blade new') RESTART(*YES)

This should solve your problems.

Bradley V. Stone
BVS/Tools
http://www.bvstools.com



> -----Original Message-----
> From: Roger Boucher [mailto:RBoucher@stanpac.com]
> Sent: Monday, July 26, 1999 6:45 PM
> To: 'MIDRANGE-L@midrange.com'
> Subject: RE: Table saw shake
> 
> 
> PWRDWNSYS OPTION(*RIPBLADE)
> 
> -----Original Message-----
> From: York, Albert [mailto:albert.york@nissan-usa.com]
> Sent: Monday, July 26, 1999 3:37 PM
> To: 'MIDRANGE-L@midrange.com'
> Subject: RE: Table saw shake
> 
> 
> You should have tried the command ENDSAWSHK REPLACE(*BELT *BLADE)
> REINSTALL(*MOTOR). 
> 
> > ----------
> > From:       Bill Paris[SMTP:bparis@sccmail.com]
> > Sent:       Monday, July 26, 1999 1:16 PM
> > To:         MIDRANGE-L@midrange.com
> > Subject:    RE: Table saw shake
> > 
> > This made sense up until the machined pulleys and the link belt...
> > *grin*
> > 
> > Bill Paris
> > Sorrento Cheese Co., Inc.
> > 716-823-6262 x376
> > 
> > I forgot to mention, in all my excitement this morning, the table
> > saw vibration went away with a belt change and reinstalling motor
> > on saw(per installation instructions)... My old belt looked fine,
> > but apparently developed a "set" from lack of use in all of 
> the recent
> > heat wave(which keeps me away from saw). I also did minor tune up of
> > fence and guard/splitter.. I also went out and purchased a new
> > Freud LU87 24 tooth thin kerf rip blade, which made a WORLD of
> > difference
> > in ripping that nasty old pressure treated 2x10's etc,etc.... I
> > thought all the hoopla about thin kerfs was just that , HOOPLA, but
> > no indeed, they do make a huge difference...
> > 
> > I also ordered a set of machined pullys and a link belt, 
> which ought to
> > help out quite a bit <>>><>><><><>
> > 
> > +---
> > | This is the Midrange System Mailing List!
> > | To submit a new message, send your mail to 
> MIDRANGE-L@midrange.com.
> > | To subscribe to this list send email to 
> MIDRANGE-L-SUB@midrange.com.
> > | To unsubscribe from this list send email to
> > MIDRANGE-L-UNSUB@midrange.com.
> > | Questions should be directed to the list owner/operator:
> > david@midrange.com
> > +---
> > 
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to 
> MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
> david@midrange.com
> +---
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to 
> MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator: 
> david@midrange.com
> +---
> 
+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---