× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



We're moving from an 800 to a 520 and did a full save on the 800 and
restore on the 520.  Updated the resource names and IP settings,
disconnected the old box from the network and fired up one of our Domino
servers on the new box.  Server does not start, joblog messages follow.
Tried firing up our Sametime and Quickplace servers on the new box and they
start OK.  Take a look at the joblog messages and let me know if anyone has
any ideas

There are two joblogs that appear after trying to start the server, one for
the SERVER job, the other for the QNNINSTS job.  The messages below are
from the SERVER job.  There does't appear to anything meaningful in the
QNNINSTS joblog.

Both boxes V5R3, same PTF levels.  Domino at 6.5.4 FP1 on both boxes

MCH3402    Escape                  40   09/30/05  15:43:56.562456  LIBNOTES
QDOMINO654  *STMT    LIBNOTES    QDOMINO654  *STMT
>From module . . . . . . . . :   CLEANUP
>From procedure  . . . . . . :   OSFaultRecoveryRemovePid
Statement . . . . . . . . . :   1
To module . . . . . . . . . :   CLEANUP
To procedure  . . . . . . . :   OSFaultRecoveryRemovePid
Statement . . . . . . . . . :   1
Message . . . . :   Tried to refer to all or part of an object that no
longer exists.
Cause . . . . . :   The most common cause is that a stored address to an
object is no longer correct because that object was deleted or part of the
object was deleted

CEE9901    Escape                  30   09/30/05  15:43:56.604296  QLEAWI
QSYS        *STMT    QP0ZPCPN    QSYS        *STMT
>From module . . . . . . . . :   QLEDEH
>From procedure  . . . . . . :   Q LE leDefaultEh
Statement . . . . . . . . . :   168
To module . . . . . . . . . :   QP0ZPCPN
To procedure  . . . . . . . :   InvokeTargetPgm__FP11qp0z_pcp_cb
Statement . . . . . . . . . :   187
Message . . . . :   Application error.  MCH3402 unmonitored by LIBNOTES at
statement 0000000001, instruction X'0000'.
Cause . . . . . :   The application ended abnormally because an exception
occurred and was not handled.  The name of the program to which the
unhandled exception is sent is LIBNOTES CLEANUP OSFaultRecoveryRemovePid.
The program was stopped at the high-level language statement number(s)
0000000001 at the time the message was sent.  If more than one statement
number is shown, the program is an optimized ILE program.  Optimization
does not allow a single statement number to be determined.  If *N is shown
as a value, it means the real value was not available.
Recovery  . . . :   See the low level messages previously listed to locate
the cause of the exception.  Correct any errors, and then try the request
again.

Bob



As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.