Re: Loading Plug-ins - ARCAD 5250 and iSphere

Dave, under the Help > Install New Software there is a link to "available
software sites" just below the add button.
This will bring up your current software sites and you mentioned you can
see a couple references to the Arcad 5250 emulator in the pull down list,
you should see them here also.
When you select them (not checking the box but selecting them so they are
highlighted) the option on the right to Remove them should be enabled.
Remove both.

Go back to the first panel and Click Add, then click Local and browse to
the unzipped folder on your desktop.
When you click OK the Arcad 5250 emulator should be listed in the list box
below so you can check it.

If not then down below there is an option 'Group Items by Category' that
is checked by default.
Uncheck it, is the Arcad 5250 emulator listed now?

Let me know if that does not resolve the issue.
Thanks


Thanks Jeffrey. I'll try to list the steps in detail.
1 I have unzipped the file
2 under Help / install new software, I see a box that says Available
Software at the top there is a work with box and then a box headed name
with one item in it that says "There is no site selected"
3 I attempt to add a repository, browse to the local folder on C for
file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/ The OK button on the add
repository box is grayed out and a message appears saying duplicate
location.
4 I cancel and click on the "Available software sites" text
5 There is a check mark on both
file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/ and
Jar:file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/
Yet when I click ok, still nothing shows under the Name box.
All that is there is a line with a check box that says There is no Site
selected.
6 If I check the box, there are no changes.
If I click the select all button, nothing changes.
7 No combination of any of my actions changes the buttons at the bottom of
the box for back, next, or Finish.
8 The only button available is Cancel.
9 Using the "Run as Administrator" option does not change any of the steps
above.

Appreciate your help.

Thanks,

Dave B




Jeffrey Tickner
Technical Resource
jtickner@xxxxxxxxxxxxxxxxx

Please only print this email if really necessary
1, Phoenix Mill Lane, Suite 203, Peterborough NH 03458 - USA
Tel. + 1 603 371 9074 ext 505
Toll. free +1 800 676 4709 ext 505
55, rue Adrastée - Parc Altais F-74650 CHAVANOD
Tel. +33 (0)4 50 57 83 96
Fax. +33 (0)4 50 57 52 79



***This e-mail and its attached documents are confidential and intended
solely for the use of the addressee(s). ARCAD Software can in no way be
held responsible for any damage resulting from an incident involving
security, integrity, virus or transmission delay. As the integrity of this
message cannot be guaranteed on Internet, the ARCAD Software company cannot
be held responsible for its contents. Any unauthorized use or dissemination
is prohibited.***



On Mar 11, 2013, at 11:42 AM, wdsci-l-request@xxxxxxxxxxxx wrote:

Send WDSCI-L mailing list submissions to
wdsci-l@xxxxxxxxxxxx

To subscribe or unsubscribe via the World Wide Web, visit
http://lists.midrange.com/mailman/listinfo/wdsci-l
or, via email, send a message with subject or body 'help' to
wdsci-l-request@xxxxxxxxxxxx

You can reach the person managing the list at
wdsci-l-owner@xxxxxxxxxxxx

When replying, please edit your Subject line so it is more specific
than "Re: Contents of WDSCI-L digest..."


*** NOTE: When replying to this digest message, PLEASE remove all text

unrelated to your reply and change the subject line so it is meaningful.

Today's Topics:

1. Re: Loading Plug-ins - ARCAD 5250 and iSphere (Paul Bailey)
2. Re: Loading Plug-ins - ARCAD 5250 and iSphere (Dave Boettcher)
3. Re: Loading Plug-ins - ARCAD 5250 and iSphere (Dave Boettcher)
4. Re: Loading Plug-ins - ARCAD 5250 and iSphere (Paul Bailey)


----------------------------------------------------------------------

message: 1
date: Mon, 11 Mar 2013 09:29:14 +0000
from: Paul Bailey <PaulBailey@xxxxxxxxxx>
subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere


I've only just installed the iSphere plugin (using the TN5250j update

site download from the http://www.taskforce-it.de/downloads.php website,
which gives me both iSphere and TN5250j in RDP 8.5.1). I extracted the zip
file to my desktop, "add"ed an update site in the "Install new software"
screen and everything went smoothly from there. I removed the update site
from my desktop afterwards.

Hope this helps.

-Paul.

________________________________________
From: wdsci-l-bounces@xxxxxxxxxxxx [wdsci-l-bounces@xxxxxxxxxxxx] On

Behalf Of Jeffrey Tickner [jtickner@xxxxxxxxxxxxxxxxx]

Sent: 10 March 2013 04:15
To: wdsci-l@xxxxxxxxxxxx
Subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere

For the Arcad 5250 plugin, the zip file must be unzipped (not renamed

jar) and you would point to the folder containing the site.xml, plugins and
features folders as a local site from the 'install new software' option.

I have run into issues with other users putting the unzipped folder on a

network drive and everything works fine until the install starts.

Other users have no issue installing from a network drive.

The installation manager has nothing to do with adding plugins so maybe

running RDP as admin might help with an update if you may have authority
issues with the install location of RDP.

If you could provide the steps involved with a specific scenario and the

specific error message that results we may be able to be more help.

Thanks


Jeffrey Tickner
Technical Resource
jtickner@xxxxxxxxxxxxxxxxx

Please only print this email if really necessary
1, Phoenix Mill Lane, Suite 203, Peterborough NH 03458 - USA
Tel. + 1 603 371 9074 ext 505
Toll. free +1 800 676 4709 ext 505
55, rue Adrast?e - Parc Altais F-74650 CHAVANOD
Tel. +33 (0)4 50 57 83 96
Fax. +33 (0)4 50 57 52 79



***This e-mail and its attached documents are confidential and intended

solely for the use of the addressee(s). ARCAD Software can in no way be
held responsible for any damage resulting from an incident involving
security, integrity, virus or transmission delay. As the integrity of this
message cannot be guaranteed on Internet, the ARCAD Software company cannot
be held responsible for its contents. Any unauthorized use or dissemination
is prohibited.***

On Mar 9, 2013, at 1:00 PM, wdsci-l-request@xxxxxxxxxxxx wrote:

Although, I have been trying to load the 5250 Arcad plug-in and the

iSphere tool that I read about lately.

No matter what I have tried - zip file or extracted jar files, with the

installation manager or with the install new software selection under help
on RDp.

I tried the -clean option that someone suggested in the archives but no

difference.

I get the message either that it couldn't find the jar file (after I

had browsed to add it).

Or the message that it can't connect to it when I was adding a

repository in installation manager. Also tried run as administrator for
installation manager.

There must be something I have set wrong somewhere but I can't figure

out what.

Is there a plug-in for dummies installation instructions somewhere.
I would appreciate any ideas. Thanks

HTH,
TIA,
Thanks,
Whichever applies

Dave B

Sometimes I get the feeling the whole world is against me, but deep

down I know that's not true. Some of the smaller countries are neutral. --
Robert Orben (comedy writer)

--
This is the Rational Developer for IBM i / Websphere Development Studio

Client for System i & iSeries (WDSCI-L) mailing list

To post a message email: WDSCI-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/wdsci-l.

Scanned by MailDefender - managed email security from intY -

www.maildefender.net

Important, this email transmission and any files with it are strictly

confidential to the intended recipient and may be legally privileged. Any
views or opinions presented are solely those of the author and do not
necessarily represent those of BHSF. If you are not the intended recipient,
you must not copy, disclose or distribute its contents in any way. If you
have received this e-mail in error, please notify the sender and delete the
e-mail from your system.

We have taken steps to ensure this email and attachments are free from

any virus but do not accept any responsibility once this e-mail has been
transmitted. You should scan any attachments for viruses. No contract may
be concluded on behalf of BHSF Limited by e-mail.

Registered Office: BHSF Limited, Gamgee House, 2 Darnley Road,

Birmingham, B16 8TE. www.bhsf.co.uk Registered in England number 35500.
BHSF is authorised and regulated by the Financial Services Authority.

------------------------------

message: 2
date: Mon, 11 Mar 2013 15:23:43 +0000
from: Dave Boettcher <Dave.Boettcher@xxxxxxxxxxxxxxxxx>
subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere

Thanks Jeffrey. I'll try to list the steps in detail.
1 I have unzipped the file
2 under Help / install new software, I see a box that says Available

Software at the top there is a work with box and then a box headed name
with one item in it that says "There is no site selected"

3 I attempt to add a repository, browse to the local folder on C for

file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/ The OK button on the add
repository box is grayed out and a message appears saying duplicate
location.

4 I cancel and click on the "Available software sites" text
5 There is a check mark on both

file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/ and

Jar:file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/
Yet when I click ok, still nothing shows under the Name box.
All that is there is a line with a check box that says There is no Site

selected.

6 If I check the box, there are no changes.
If I click the select all button, nothing changes.
7 No combination of any of my actions changes the buttons at the bottom

of the box for back, next, or Finish.

8 The only button available is Cancel.
9 Using the "Run as Administrator" option does not change any of the

steps above.

Appreciate your help.

Thanks,

Dave B

Sometimes I get the feeling the whole world is against me, but deep down

I know that's not true. Some of the smaller countries are neutral. --
Robert Orben (comedy writer)

-----Original Message-----
From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]

On Behalf Of Jeffrey Tickner

Sent: Saturday, March 09, 2013 10:15 PM
To: wdsci-l@xxxxxxxxxxxx
Subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere

For the Arcad 5250 plugin, the zip file must be unzipped (not renamed

jar) and you would point to the folder containing the site.xml, plugins and
features folders as a local site from the 'install new software' option.

I have run into issues with other users putting the unzipped folder on a

network drive and everything works fine until the install starts.

Other users have no issue installing from a network drive.

The installation manager has nothing to do with adding plugins so maybe

running RDP as admin might help with an update if you may have authority
issues with the install location of RDP.

If you could provide the steps involved with a specific scenario and the

specific error message that results we may be able to be more help.

Thanks


Jeffrey Tickner
Technical Resource
jtickner@xxxxxxxxxxxxxxxxx

Please only print this email if really necessary 1, Phoenix Mill Lane,

Suite 203, Peterborough NH 03458 - USA Tel. + 1 603 371 9074 ext 505Toll. free +1
800 676 4709 ext 505 55, rue Adrast?e - Parc Altais F-74650 CHAVANOD Tel. +33
(0)4 50 57 83 96 Fax. +33 (0)4 50 57 52 79

***This e-mail and its attached documents are confidential and intended

solely for the use of the addressee(s). ARCAD Software can in no way be
held responsible for any damage resulting from an incident involving
security, integrity, virus or transmission delay. As the integrity of this
message cannot be guaranteed on Internet, the ARCAD Software company cannot
be held responsible for its contents. Any unauthorized use or dissemination
is prohibited.***

On Mar 9, 2013, at 1:00 PM, wdsci-l-request@xxxxxxxxxxxx wrote:

Although, I have been trying to load the 5250 Arcad plug-in and the

iSphere tool that I read about lately.

No matter what I have tried - zip file or extracted jar files, with the

installation manager or with the install new software selection under help
on RDp.

I tried the -clean option that someone suggested in the archives but no

difference.

I get the message either that it couldn't find the jar file (after I

had browsed to add it).

Or the message that it can't connect to it when I was adding a

repository in installation manager. Also tried run as administrator for
installation manager.

There must be something I have set wrong somewhere but I can't figure

out what.

Is there a plug-in for dummies installation instructions somewhere.
I would appreciate any ideas. Thanks

HTH,
TIA,
Thanks,
Whichever applies

Dave B

Sometimes I get the feeling the whole world is against me, but deep
down I know that's not true. Some of the smaller countries are
neutral. -- Robert Orben (comedy writer)

--
This is the Rational Developer for IBM i / Websphere Development Studio

Client for System i & iSeries (WDSCI-L) mailing list To post a message
email: WDSCI-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change list
options,

visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives at

http://archive.midrange.com/wdsci-l.

------------------------------

message: 3
date: Mon, 11 Mar 2013 15:26:50 +0000
from: Dave Boettcher <Dave.Boettcher@xxxxxxxxxxxxxxxxx>
subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere

I see I missed saying that the buttons at the bottom of the box are

grayed out at all times.

Thanks,

Dave B

Sometimes I get the feeling the whole world is against me, but deep down

I know that's not true. Some of the smaller countries are neutral. --
Robert Orben (comedy writer)

-----Original Message-----
From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]

On Behalf Of Dave Boettcher

Sent: Monday, March 11, 2013 10:24 AM
To: Rational Developer for IBM i / Websphere Development Studio Client

for System i & iSeries

Subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere

Thanks Jeffrey. I'll try to list the steps in detail.
1 I have unzipped the file
2 under Help / install new software, I see a box that says Available

Software at the top there is a work with box and then a box headed name
with one item in it that says "There is no site selected"

3 I attempt to add a repository, browse to the local folder on C for

file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/ The OK button on the add
repository box is grayed out and a message appears saying duplicate
location.

4 I cancel and click on the "Available software sites" text
5 There is a check mark on both

file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/ and
Jar:file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/

Yet when I click ok, still nothing shows under the Name box.
All that is there is a line with a check box that says There is no Site

selected.

6 If I check the box, there are no changes.
If I click the select all button, nothing changes.
7 No combination of any of my actions changes the buttons at the bottom

of the box for back, next, or Finish.

8 The only button available is Cancel.
9 Using the "Run as Administrator" option does not change any of the

steps above.

Appreciate your help.

Thanks,

Dave B

Sometimes I get the feeling the whole world is against me, but deep down

I know that's not true. Some of the smaller countries are neutral. --
Robert Orben (comedy writer)

-----Original Message-----
From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]

On Behalf Of Jeffrey Tickner

Sent: Saturday, March 09, 2013 10:15 PM
To: wdsci-l@xxxxxxxxxxxx
Subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere

For the Arcad 5250 plugin, the zip file must be unzipped (not renamed

jar) and you would point to the folder containing the site.xml, plugins and
features folders as a local site from the 'install new software' option.

I have run into issues with other users putting the unzipped folder on a

network drive and everything works fine until the install starts.

Other users have no issue installing from a network drive.

The installation manager has nothing to do with adding plugins so maybe

running RDP as admin might help with an update if you may have authority
issues with the install location of RDP.

If you could provide the steps involved with a specific scenario and the

specific error message that results we may be able to be more help.

Thanks


Jeffrey Tickner
Technical Resource
jtickner@xxxxxxxxxxxxxxxxx

Please only print this email if really necessary 1, Phoenix Mill Lane,

Suite 203, Peterborough NH 03458 - USA Tel. + 1 603 371 9074 ext 505 Toll.
free +1 800 676 4709 ext 505 55, rue Adrast?e - Parc Altais F-74650
CHAVANOD Tel. +33 (0)4 50 57 83 96 Fax. +33 (0)4 50 57 52 79

***This e-mail and its attached documents are confidential and intended

solely for the use of the addressee(s). ARCAD Software can in no way be
held responsible for any damage resulting from an incident involving
security, integrity, virus or transmission delay. As the integrity of this
message cannot be guaranteed on Internet, the ARCAD Software company cannot
be held responsible for its contents. Any unauthorized use or dissemination
is prohibited.***

On Mar 9, 2013, at 1:00 PM, wdsci-l-request@xxxxxxxxxxxx wrote:

Although, I have been trying to load the 5250 Arcad plug-in and the

iSphere tool that I read about lately.

No matter what I have tried - zip file or extracted jar files, with the

installation manager or with the install new software selection under help
on RDp.

I tried the -clean option that someone suggested in the archives but no

difference.

I get the message either that it couldn't find the jar file (after I

had browsed to add it).

Or the message that it can't connect to it when I was adding a

repository in installation manager. Also tried run as administrator for
installation manager.

There must be something I have set wrong somewhere but I can't figure

out what.

Is there a plug-in for dummies installation instructions somewhere.
I would appreciate any ideas. Thanks

HTH,
TIA,
Thanks,
Whichever applies

Dave B

Sometimes I get the feeling the whole world is against me, but deep
down I know that's not true. Some of the smaller countries are
neutral. -- Robert Orben (comedy writer)

--
This is the Rational Developer for IBM i / Websphere Development Studio

Client for System i & iSeries (WDSCI-L) mailing list To post a message
email: WDSCI-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change list
options,

visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives at

http://archive.midrange.com/wdsci-l.

--
This is the Rational Developer for IBM i / Websphere Development Studio

Client for System i & iSeries (WDSCI-L) mailing list To post a message
email: WDSCI-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change list
options,

visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives at

http://archive.midrange.com/wdsci-l.

------------------------------

message: 4
date: Mon, 11 Mar 2013 15:42:33 +0000
from: Paul Bailey <PaulBailey@xxxxxxxxxx>
subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere


In the box at the very top that says "Type or select a site", have you

dropped the list down to select the ARCAD site you've entered?

Also, on one plugin I've installed before, I sometimes need to deselect

the "Group items by category" check box. When I do that, the "There is no
site selected" box then lists the items that can be selected.

Final check, have you got the "Hide items that are already installed"

check box checked? If so then it might be likely that you already have
ARCAD installed. (You can check by clicking the "already installed" link
and working through the displayed lists to see if you can spot ARCAD, or
something that is written by ARCAD's developer.)

-Paul.


________________________________________
From: wdsci-l-bounces@xxxxxxxxxxxx [wdsci-l-bounces@xxxxxxxxxxxx] On

Behalf Of Dave Boettcher [Dave.Boettcher@xxxxxxxxxxxxxxxxx]

Sent: 11 March 2013 15:26
To: Rational Developer for IBM i / Websphere Development Studio Client

for System i & iSeries

Subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere

I see I missed saying that the buttons at the bottom of the box are

grayed out at all times.

Thanks,

Dave B

Sometimes I get the feeling the whole world is against me, but deep down

I know that's not true. Some of the smaller countries are neutral. --
Robert Orben (comedy writer)

-----Original Message-----
From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]

On Behalf Of Dave Boettcher

Sent: Monday, March 11, 2013 10:24 AM
To: Rational Developer for IBM i / Websphere Development Studio Client

for System i & iSeries

Subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere

Thanks Jeffrey. I'll try to list the steps in detail.
1 I have unzipped the file
2 under Help / install new software, I see a box that says Available

Software at the top there is a work with box and then a box headed name
with one item in it that says "There is no site selected"

3 I attempt to add a repository, browse to the local folder on C for

file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/ The OK button on the add
repository box is grayed out and a message appears saying duplicate
location.

4 I cancel and click on the "Available software sites" text
5 There is a check mark on both

file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/ and
Jar:file:/C:/ARCAD_5250_emulator_for_eclipse_RDi/

Yet when I click ok, still nothing shows under the Name box.
All that is there is a line with a check box that says There is no Site

selected.

6 If I check the box, there are no changes.
If I click the select all button, nothing changes.
7 No combination of any of my actions changes the buttons at the bottom

of the box for back, next, or Finish.

8 The only button available is Cancel.
9 Using the "Run as Administrator" option does not change any of the

steps above.

Appreciate your help.

Thanks,

Dave B

Sometimes I get the feeling the whole world is against me, but deep down

I know that's not true. Some of the smaller countries are neutral. --
Robert Orben (comedy writer)

-----Original Message-----
From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]

On Behalf Of Jeffrey Tickner

Sent: Saturday, March 09, 2013 10:15 PM
To: wdsci-l@xxxxxxxxxxxx
Subject: Re: [WDSCI-L] Loading Plug-ins - ARCAD 5250 and iSphere

For the Arcad 5250 plugin, the zip file must be unzipped (not renamed

jar) and you would point to the folder containing the site.xml, plugins and
features folders as a local site from the 'install new software' option.

I have run into issues with other users putting the unzipped folder on a

network drive and everything works fine until the install starts.

Other users have no issue installing from a network drive.

The installation manager has nothing to do with adding plugins so maybe

running RDP as admin might help with an update if you may have authority
issues with the install location of RDP.

If you could provide the steps involved with a specific scenario and the

specific error message that results we may be able to be more help.

Thanks


Jeffrey Tickner
Technical Resource
jtickner@xxxxxxxxxxxxxxxxx

Please only print this email if really necessary 1, Phoenix Mill Lane,

Suite 203, Peterborough NH 03458 - USA Tel. + 1 603 371 9074 ext 505 Toll.
free +1 800 676 4709 ext 505 55, rue Adrast?e - Parc Altais F-74650
CHAVANOD Tel. +33 (0)4 50 57 83 96 Fax. +33 (0)4 50 57 52 79

***This e-mail and its attached documents are confidential and intended

solely for the use of the addressee(s). ARCAD Software can in no way be
held responsible for any damage resulting from an incident involving
security, integrity, virus or transmission delay. As the integrity of this
message cannot be guaranteed on Internet, the ARCAD Software company cannot
be held responsible for its contents. Any unauthorized use or dissemination
is prohibited.***

On Mar 9, 2013, at 1:00 PM, wdsci-l-request@xxxxxxxxxxxx wrote:

Although, I have been trying to load the 5250 Arcad plug-in and the

iSphere tool that I read about lately.

No matter what I have tried - zip file or extracted jar files, with the

installation manager or with the install new software selection under help
on RDp.

I tried the -clean option that someone suggested in the archives but no

difference.

I get the message either that it couldn't find the jar file (after I

had browsed to add it).

Or the message that it can't connect to it when I was adding a

repository in installation manager. Also tried run as administrator for
installation manager.

There must be something I have set wrong somewhere but I can't figure

out what.

Is there a plug-in for dummies installation instructions somewhere.
I would appreciate any ideas. Thanks

HTH,
TIA,
Thanks,
Whichever applies

Dave B

Sometimes I get the feeling the whole world is against me, but deep
down I know that's not true. Some of the smaller countries are
neutral. -- Robert Orben (comedy writer)

--
This is the Rational Developer for IBM i / Websphere Development Studio

Client for System i & iSeries (WDSCI-L) mailing list To post a message
email: WDSCI-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change list
options,

visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives at

http://archive.midrange.com/wdsci-l.

--
This is the Rational Developer for IBM i / Websphere Development Studio

Client for System i & iSeries (WDSCI-L) mailing list To post a message
email: WDSCI-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change list
options,

visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives at

http://archive.midrange.com/wdsci-l.

--
This is the Rational Developer for IBM i / Websphere Development Studio

Client for System i & iSeries (WDSCI-L) mailing list

To post a message email: WDSCI-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/wdsci-l.

Scanned by MailDefender - managed email security from intY -

www.maildefender.net

Important, this email transmission and any files with it are strictly

confidential to the intended recipient and may be legally privileged. Any
views or opinions presented are solely those of the author and do not
necessarily represent those of BHSF. If you are not the intended recipient,
you must not copy, disclose or distribute its contents in any way. If you
have received this e-mail in error, please notify the sender and delete the
e-mail from your system.

We have taken steps to ensure this email and attachments are free from

any virus but do not accept any responsibility once this e-mail has been
transmitted. You should scan any attachments for viruses. No contract may
be concluded on behalf of BHSF Limited by e-mail.

Registered Office: BHSF Limited, Gamgee House, 2 Darnley Road,

Birmingham, B16 8TE. www.bhsf.co.uk Registered in England number 35500.
BHSF is authorised and regulated by the Financial Services Authority.

------------------------------

--
This is the Rational Developer for IBM i / Websphere Development Studio

Client for System i & iSeries (WDSCI-L) digest list

To post a message email: WDSCI-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/wdsci-l.


End of WDSCI-L Digest, Vol 11, Issue 109
****************************************

--
This is the Rational Developer for IBM i / Websphere Development Studio
Client for System i & iSeries (WDSCI-L) mailing list
To post a message email: WDSCI-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/wdsci-l.