RE: How to get rid of message CPF4028 on Display Screen

Hi Booth, Opening in Input-Add mode solved the problem!I must have overlooked 
it during development phase.
Thank you all for your help.

Regards,
Sachin 


-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx
[mailto:rpg400-l-bounces@xxxxxxxxxxxx]On Behalf Of Chaudhary, Sachin (GE
Indust, ES Rail, consultant)
Sent: Monday, August 21, 2006 4:06 PM
To: RPG programming on the AS400 / iSeries
Subject: RE: How to get rid of message CPF4028 on Display Screen


I think I have already tried IF with ADD mode, but it never worked at the time 
I was developing it.

Regards,
Sachin


-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx
[mailto:rpg400-l-bounces@xxxxxxxxxxxx]On Behalf Of Booth Martin
Sent: Monday, August 21, 2006 4:04 PM
To: RPG programming on the AS400 / iSeries
Subject: Re: How to get rid of message CPF4028 on Display Screen


Does the file already exist?  If so, Output really doesn't work good.

I believe if you change the F-Spec for that file to Input-Full with an A 
for adding records that your problem will go away.  Or, even 
Update-Full, however that is not needed as you are not updating records.


My work is never guaranteed, and often not quite right, but this should 
work for you.



Chaudhary, Sachin (GE Indust, ES Rail, consultant) wrote:

Hi, 
I don't want the users to see the message, it does not matter how this file 
is opened, I am only writing records to this file in one of the IF conditions.

It is because of the condition code 1:
 Message . . . . :   Open of member SPDTLWRK was changed to SEQONLY(*NO).
 Cause . . . . . :   Member SPDTLWRK file SPDTLWRK in library TEST#UT2 was
   opened with the SEQONLY(*YES) parameter specified in the program or on the
   Override Database File (OVRDBF) command. However, the parameter has been
   changed to SEQONLY(*NO) because of condition 1 shown below:
     1 - The program opened member SPDTLWRK for output operations only and
   SEQONLY(*YES) was specified with the default number of records.
   SEQONLY(*YES) was changed to SEQONLY(*NO) to allow the program to handle
   duplicate key, conversion mapping, key mapping, and select or omit errors,
   or both select and omit errors at the time of the output operation.

Regards,
Sachin


-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx
[mailto:rpg400-l-bounces@xxxxxxxxxxxx]On Behalf Of Bob Cozzi
Sent: Monday, August 21, 2006 3:23 PM
To: 'RPG programming on the AS400 / iSeries'
Subject: RE: How to get rid of message CPF4028 on Display Screen


Do you want to prevent it from displaying the message or do you want to 
prevent
the sequential opening so that the message is never generated?

-Bob Cozzi
www.iSeriesTV.com
Ask your Manager to watch iSeriesTV.com


-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx [mailto:rpg400-l-bounces@xxxxxxxxxxxx] On
Behalf Of Chaudhary, Sachin (GE Indust, ES Rail,consultant)
Sent: Monday, August 21, 2006 3:04 PM
To: RPG programming on the AS400 / iSeries
Subject: How to get rid of message CPF4028 on Display Screen

Hi 
I am using a file in Output mode in RPG program, and at time of displaying the
screen the system shows diagnostic message CPF4028. I have tried overriding 
the
file to SEQONLY(*NO) in the same pgm [before opening the file in User 
Controlled
mode], but it does not work .
Can anyone help?

Thanks
Sachin