RE: H spec Option(*SrcStmt : *NoDeBugIO)

["Bob Cozzi" <cozzi@xxxxxxxxx>]

Eric,
Read my response again.
You say the "OPTION" keyword in the header spec (which I highly recommend)
is the same as the "DGBVIEW" keyword on the command. They are different.
DBGVIEW is NOT supported on the Header spec. Never has been.

"Recommend"?  I simply gave him an answer to his question. I happen to
change the default for the compiler commands on each release for the DBGVIEW
parameter, which I happen to believe have the wrong default values. 

-Bob Cozzi
www.RPGxTools.com
If everything is under control, you are going too slow.
- Mario Andretti


-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx [mailto:rpg400-l-bounces@xxxxxxxxxxxx]
On Behalf Of DeLong, Eric
Sent: Wednesday, May 11, 2005 12:03 PM
To: 'RPG programming on the AS400 / iSeries'
Subject: RE: H spec Option(*SrcStmt : *NoDeBugIO)

What?!?  Why oh why would you recommend changing compiler defaults?  Simply
adding this H spec will handle the issue with requiring a command default
value.  As I recall, this was available in V4R4.....

H Option(*SrcStmt:*NoDebugIO)



Eric DeLong
Sally Beauty Company
MIS-Project Manager (BSG)
940-297-2863 or ext. 1863



-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx
[mailto:rpg400-l-bounces@xxxxxxxxxxxx]On Behalf Of Bob Cozzi
Sent: Tuesday, May 10, 2005 11:30 AM
To: 'RPG programming on the AS400 / iSeries'
Subject: RE: H spec Option(*SrcStmt : *NoDeBugIO)


Again, this is not a V5R3 issue. It is a compiler parameter issue.
Run this if you want to:

CHGCMDDFT CMD(CRTBNDRPG) NEWDFT('dbgview(*source)')   
and
CHGCMDDFT CMD(CRTRPGMOD) NEWDFT('dbgview(*source)')   

And you'll end up with the same results as you had on your earlier release.

-Bob Cozzi
www.RPGxTools.com
If everything is under control, you are going too slow.
- Mario Andretti


-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx [mailto:rpg400-l-bounces@xxxxxxxxxxxx]
On Behalf Of Gary Palomino
Sent: Tuesday, May 10, 2005 11:17 AM
To: RPG400-L@xxxxxxxxxxxx
Subject: H spec Option(*SrcStmt : *NoDeBugIO)

We just upgraded from V4R5 to V5R3.

The programs compiled on the new version does not show the source
statemets when debugging. If we prompt the compile and change
DBGVIEW(*SOURCE) from DBGVIEW(*STMT) it works.

Is there a control H spec that it will show the source statement on
V5R3?

Gary
-- 
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.




-- 
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.


-- 
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.