RE: Communication lines

[pytel@xxxxxxxxxx]

Check DSCTMR (Disconnect Timer parameter) for APPC *CTLD.
If you have SWTDSC(*YES) and NO ACTIVE sessions, then after DSCTMR timer
expires, switched line should be dropped.
When line stays up, when you think it should not, check active sessions on APPC
device description - DSPMODSTS command or option 9 from WRKCFGSTS screen. Check
active modes and active sessions. This may give you a clue, what holds your line
up.

(Do you have switched line, by the way ? - disconnect will not work on a leased
line.)

Good luck
    Alexei Pytel



Bill Brosch <bbrosch@stecnet.com> on 07/14/99 08:49:20 AM

Please respond to RPG400-L@midrange.com

To:   "'RPG400-L@midrange.com'" <RPG400-L@midrange.com>
cc:    (bcc: Alexei Pytel/Rochester/IBM)
Subject:  RE: Communication lines





Tried your suggestion, but could not change the CPSSN value.  That parm
is only for APPN devices, & we're using APPC.  Changing the other
entries had no affect (on either end or both ends).


-----Original Message-----
From: pytel@us.ibm.com [mailto:pytel@us.ibm.com]
Sent: Tuesday, July 13, 1999 10:39 AM
To: RPG400-L@midrange.com
Subject: Re: Communication lines


Configure APPC controller with DIALINIT(*DELAY) SWTDSC(*YES) CPSSN(*NO).
DIALINIT(*DELAY) will make line connect only on session request.
SWTDSC(*YES) will drop the line, when no sessions active.
CPSSN(*NO) will disallow permanent session between systems.

Best regards
    Alexei Pytel



Bill Brosch <bbrosch@stecnet.com> on 07/13/99 08:39:50 AM

Please respond to RPG400-L@midrange.com

To:   RPG400-L@midrange.com
cc:    (bcc: Alexei Pytel/Rochester/IBM)
Subject:  Communication lines





Hello everyone!

I have some dial-up appc communication lines set up to other as/400s for
snads traffic.  Unfortunatley, the lines stay actice after the last file
has been transmitted.  Is there any way of dropping the line when there
are no active jobs on it?

Thanks,

Bill Brosch
Swift Technologies
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*
* This is the RPG/400 Discussion Mailing List!  To submit a new
*
* message, send your mail to "RPG400-L@midrange.com".  To unsubscribe
*
* from this list send email to MAJORDOMO@midrange.com and specify
*
* 'unsubscribe RPG400-L' in the body of your message.  Questions should
*
* be directed to the list owner / operator: david@midrange.com
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*



* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*
* This is the RPG/400 Discussion Mailing List!  To submit a new
*
* message, send your mail to "RPG400-L@midrange.com".  To unsubscribe
*
* from this list send email to MAJORDOMO@midrange.com and specify
*
* 'unsubscribe RPG400-L' in the body of your message.  Questions should
*
* be directed to the list owner / operator: david@midrange.com
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* This is the RPG/400 Discussion Mailing List!  To submit a new         *
* message, send your mail to "RPG400-L@midrange.com".  To unsubscribe   *
* from this list send email to MAJORDOMO@midrange.com and specify       *
* 'unsubscribe RPG400-L' in the body of your message.  Questions should *
* be directed to the list owner / operator: david@midrange.com          *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *



* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* This is the RPG/400 Discussion Mailing List!  To submit a new         *
* message, send your mail to "RPG400-L@midrange.com".  To unsubscribe   *
* from this list send email to MAJORDOMO@midrange.com and specify       *
* 'unsubscribe RPG400-L' in the body of your message.  Questions should *
* be directed to the list owner / operator: david@midrange.com          *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *