|
Well I can say this with certainty, I have loaded IBM i 7.2 from--
TS2900 with a FC #57B4 adapter on a POWER8. I have loaded IBM i 7.2
from TS2900 onto a Power6 even but with an older adapter.
The tape needs to be loaded into the tape drive from the front panel.
On these newer drives I've never had to switch to sequential or
library mode just have the drive loaded.
Do you have an HMC attached?
- Larry "DrFranken" Bolhuis
www.Frankeni.com
www.iDevCloud.com - Personal Development IBM i timeshare service.
www.iInTheCloud.com - Commercial IBM i Cloud Hosting.
On 7/14/2015 8:46 PM, Evan Harris wrote:
Hi Larry
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
It is attached to the bottom port. I had an Alt-D IPL going for a
good hour with nothing happening - just stuck on the same SRC (C200
4150 I think, but don't quote me on that)
I may have misunderstood something, but this page seemed to indicate
the
TS2900 couldn't be used for an Alt-IPL with the card I am using to
attach
it:
https://www.ibm.com/developerworks/community/wikis/home?lang=en#!/wik
i/IBM%20Removable%20Media%20on%20IBM%20i/page/IBM%20i%20Tape%20and%20
optical%20on%20Power%208
"*Note: *SAS tape library devices are not supported, with the
exception of
TS2900 in sequential mode, when attached using a VIOS partition."
Re-reading that I think it could be saying that SAS tape libraries
are not supported by VIOS except for the TS2900 in sequential mode,
though I originally read it the other way (i..e TS2900 not supported)
If it is supported it sure is doing it's best not to work. I really
can't think what else to check/change. Normally these things are simple...
On Wed, Jul 15, 2015 at 12:26 PM, DrFranken <midrange@xxxxxxxxxxxx>
wrote:
Which port is the tape drive attached to? It needs to be the bottom port.
There is no reason the TS2900 isn't a valid alt-IPL device.
- Larry "DrFranken" Bolhuis
www.Frankeni.com
www.iDevCloud.com - Personal Development IBM i timeshare service.
www.iInTheCloud.com - Commercial IBM i Cloud Hosting.
On 7/14/2015 6:51 PM, Evan Harris wrote:
Yeah I am aware of that. The LIC level is basically the same as
the OS on
the tape and I will be re-applying all the required PTF's so IThis is the Midrange Systems Technical Discussion (MIDRANGE-L)
should be OK.
On Wed, Jul 15, 2015 at 10:43 AM, <tsetso.marinov@xxxxxxxxx> wrote:
Hi,
--
You know that it can get funny, if you restore the LIC from the
DVD and then load the OS from tape with different levels ot the PTF's.
It's not mandatory that you will encounter an issue but according
to IBM you can have an unsupported configuration.
Regards
Sent by Outlook for Android
On Tue, Jul 14, 2015 at 1:48 PM -0700, "Evan Harris" <
auctionitis@xxxxxxxxx> wrote:
Hi guys
I am currently doing a build of a new test system for a customer
and having a few hiccups along the way.
The machine I am using is a new Power 8 S824 6. It has a TS2900
tape library with HH LTO6 attached to a 57B4 SAS adapter. It is
intended to run the IBM i Operating system (no VIOS)
The problems I am having are around getting the tape drive
visible. It is not supported as an ALT-IPL device as far as I can
tell from the IBM docs.
That's OK, I half expected that and have a V7R1 DVD to boot from
which according to me is resave level RS-710-N so V7R1 TR10.
Despite that I can't seem to get the tape library visible as an
alternate installation device either after booting from DVD.
The library is currently set to sequential mode as an autoloader.
I have an option 21 save from the customer test system and at this
point what I am thinking about doing is installing LIC form the
DVD and then installing Base OS from DVD as well. After that I
will do the rest of the recovery from Tape and then go back and
reload/re-apply all the PTFs.
Anybody got any other suggestions as to what I missed or what I
can try ?
If the config is not quite supported that's OK, I'd just like to
know that;s the case (haven't been able to track down a definitive
IBM doc as
yet) - I didn't do the config I just got sent out to make it work....
--
Regards
Evan Harris
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L)
mailing list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To
subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please
take a moment to review the archives at
http://archive.midrange.com/midrange-l.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L)
mailing list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To
subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please
take a moment to review the archives at
http://archive.midrange.com/midrange-l.
mailing list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To
subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please
take a moment to review the archives at
http://archive.midrange.com/midrange-l.
--
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take
a moment to review the archives at
http://archive.midrange.com/midrange-l.
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.
midrange.com
