× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



I'm leaning towards the Arduino myself (in fact i may have to implement it
for my DC, even though i have no POWER systems running there), with the
Arduino you can also monitor temperatures, input voltage ranges, and
interface with normal and inexpensive UPS (compared to the ups that have
the relay output required for POWER). You can have 2 rs232 UPS which also
report neat stuff like "time remaining on battery" which is better than
having a dumb timer and starting a shutdown...
On the same page, is there any command to prompt the system to flush main
storage? (i mean, do the d9002740 and d6000298 steps beforehand or at least
part of them)?
Maybe if there was you could implement say:
On power failure start a timer,
If power failure lasts more than X minutes, start flushing
If battery has less than X minutes, start shutdown (but this shutdown would
take less since changed pages have already been flushed)...
I ask because i've seen machines take ages to flush (specially machines
with lots of ram and slow disk controllers)


On Wed, Dec 11, 2013 at 6:38 PM, Buck Calabro <kc2hiz@xxxxxxxxx> wrote:

On 12/11/2013 4:11 PM, Jerry Draper wrote:
We use the MONUPSPWR CL IBM gives us to monitor a msgq for UPS statuses.

We take appropriate action depending on what messages we get (or not).

Now we have a situation where we have redundant AC on our IBMi connected
to two different UPS systems. (redundency of the redundent).

We only have one port on the IBMi for a UPS sensor cable.

IBM suggests a box with two UPS inputs to resolve to one UPS cable that
attaches to the IBMi so if either UPS system said we were on UPS we
would act as though we were on UPS.

Jerry

I think the consensus is rapidly forming that there's no commercial box
that 'combines' the outputs of multiple UPS units. That puts you in DIY
land. Generally speaking, if I say 'diode or' and you say 'huh?' it's a
signal to me that I should advise you to hire this out locally.

--buck

On 12/11/2013 12:48 PM, Roberto José Etcheverry Romero wrote:
Depends on one's need. I would like my system to stay up if one grid
lost
power but the other was OK (not running on battery). Some people might
want
to start a shutdown when only one of them fails. The Arduino path is
what i
meant when i said a tinkerer is the best choice to implement this, i'm
26
but i would've done it with logic gates, even simpler (less points of
failure, unless you want TCPIP monitoring, which an arduino can give
you).


On Wed, Dec 11, 2013 at 5:32 PM, DrFranken <midrange@xxxxxxxxxxxx>
wrote:

Would you want the system to power down if only one UPS lost grid
power?
Would you want the system to power down if BOTH UPS lost input power?

Looking to understand the logic in the magic box because an Arduino
could do this very very easily.

- Larry "DrFranken" Bolhuis

www.frankeni.com
www.iDevCloud.com
www.iInTheCloud.com

On 12/11/2013 2:07 PM, Jerry Draper wrote:

We have an 8202-E4D with redundant power supplies (2 AC).

Mgmt wants to connect each AC to a different UPS for UPS redundancy.

We only have one port for the RJ45 UPS sensor cable (P1-T2).



http://pic.dhe.ibm.com/infocenter/powersys/v3r1m5/index.jsp?topic=%2Fp7had%2Fp7hadups.htm


IBM suggested that we could build a box with two RJ45 in and one RJ45
out (or two DB9 to one DB9) that would detect UPS status from either
UPS
and send one signal to the IBMi.

Anyone have this box or know where to get one?

Thanks,

Jerry
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.



As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.