Chuck --
I took care of the CUME and group PTFs after the OS/400 restore.
The SCPF spool file shows multiple error messages:
MCH3402 Escape 40 01/02/13 13:57:43.967456 < allProgram 00005C QLEAWI QSYS *STMT
From Program . . . . . . . : AiUpcallProgram
To module . . . . . . . . . : QLEPM
To procedure . . . . . . . : Q LE leActivationInit
Statement . . . . . . . . . : 181
Message . . . . : Tried to refer to all or part of an object that no longer
exists.
Cause . . . . . : The most common cause is that a stored address to an
object is no longer correct because that object was deleted or part of the
object was deleted.
CEE9901 Escape 30 01/02/13 13:57:43.967688 QLEAWI QSYS *STMT QSZSTPRD QSYS 0779
From module . . . . . . . . : QLEDEH
From procedure . . . . . . : Q LE leDefaultEh
Statement . . . . . . . . . : 205
Message . . . . : Application error. MCH3402 unmonitored by QLEAWI at
statement 0000000181, instruction X'0000'.
Cause . . . . . : The application ended abnormally because an exception
occurred and was not handled. The name of the program to which the
unhandled exception is sent is QLEAWI QLEPM Q LE leActivationInit. The
program was stopped at the high-level language statement number(s)
0000000181 at the time the message was sent. If more than one statement
number is shown, the program is an optimized ILE program. Optimization does
not allow a single statement number to be determined. If *N is shown as a
value, it means the real value was not available. Recovery . . . : See
the low level messages previously listed to locate the cause of the
exception. Correct any errors, and then try the request again.
CPF9999 Escape 40 01/02/13 13:57:43.967840 QMHUNMSG *N QSZSTPRD QSYS 0779
Message . . . . : Function check. CEE9901 unmonitored by QSZSTPRD at
statement *N, instruction X'0779'.
Cause . . . . . : An escape exception message was sent to a program which
did not monitor for that message. The full name of the program to which the
unmonitored message was sent is QSZSTPRD . At the time the message was sent
the program was stopped at higher level language statement number(s) *N. If
more than one statement number is shown, the program was a bound program.
Optimization does not allow a single statement number to be determined. If
*N is shown as a value, it means the actual value was not available.
Recovery . . . : See the low level messages previously listed to locate
the cause of the function check. Correct any errors, and then try the
request again.
Repeats over and over.
Scott
________________________________
Scott Schollenberger
Vice President, Research & Development
P: 610-239-9988 x305
F: 610-239-9995
E: SSchollenberger@xxxxxxxxxxxxxxxxxx
[
http://www.harriscomputer.com/images/signatures/HarrisSchools.gif]
[
http://www.harriscomputer.com/images/signatures/DivisionofHarris.gif]<
http://www.harriscomputer.com/>
100-2011 Renaissance Blvd.
King of Prussia, PA
19406
www.harris-schoolsolutions.com<
http://www.harris-schoolsolutions.com>
This message is intended exclusively for the individual or entity to which it is addressed. This communication may contain information that is proprietary, privileged or confidential or otherwise legally exempt from disclosure. If you are not the named addressee, you are not authorized to read, print, retain, copy or disseminate this message or any part of it. If you have received this message in error, please notify the sender immediately by e-mail and delete all copies of the message.
midrange.com
