Re: Remote power up of System i 520

The rj45 port on the front of the panel, would it also work for this?
i have never used serial console for the ASMI...
Best Regards,
Roberto

On Sun, Dec 30, 2012 at 8:37 PM, DrFranken <midrange@xxxxxxxxxxxx> wrote:

AND if you still can't connect after you get the addresses using Code
30, then "Plan B" is to connect a serial cable (Cisco 'Blue Cable' or
similar) at 9600,8,n,1 to one of the serial ports on the back of the
machine and lot in to ASMI that way. Now you can also change the IP if
needed.

- DrFranken

On 12/30/2012 9:53 AM, Pete Massiello - ML wrote:

Jeff,

To find out the address of your ASMI port, on the bezel, go to Sequence 30 (will have to be in manual mode first), and the 2 addresses are the HMC1 and HMC2 port respectively.

Pete

--
Pete Massiello
iTech Solutions
http://www.itechsol.com
http://www.iInTheCloud.com




-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jeff Crosby
Sent: Friday, December 28, 2012 3:04 PM
To: Midrange Systems Technical Discussion
Subject: Re: Remote power up of System i 520

Don't laugh at this idea.

2 PCs here can function as LAN Console. Each has 2 NIC cards, with the 2nd NIC dedicated to the LAN Console connection. There is a single Linksys switch on top of the System i rack with 3 ethernet cables attached:

1) To the T5 (I think) jack on the System i (10.10.10.1)
2) To my PC (10.10.10.2)
3) To the office manager's PC (10.10.10.3)

This is a completely isolated network. If I run an ethernet cable from the ASMI to that switch and can figure out the IP address of the ASMI, can I just point a browser from my PC to https://xxx.xxx.xxx.xxx where xxx.xxx.xxx.xxx is the IP address? And then I could RDP to my desktop from home and away we go?



On Fri, Dec 28, 2012 at 2:26 PM, Kirk Goins <kirkgoins@xxxxxxxxx> wrote:

I think this will work and says about $10K for an HMC...
Find the default AMSI/HMC port IP addresses for your system Attach a
laptop to which ever HMC port you choose using the same IP subnet as
the port you are attaching to Open a browser session and log in to
AMSI Set the other HMC port to an address that is compatible with your
local network including Gateway address Cable up that port up to the
local network and access AMSI In there I believe you can Power Up the
Managed System.

.



On Fri, Dec 28, 2012 at 11:18 AM, Jeff Crosby
<jlcrosby@xxxxxxxxxxxxxxxx

wrote:
Short of an HMC, is there any way to remotely power up a System i 520?

I have LAN Console and Remote Control Panel on my desktop at work.
Due

to

power issues last week (low voltage from utility) after a power
outage, I changed QPWRRSTIPL to 0 for no power up when power is restored.

In a future outage that results in my power handling program
shutting

down

the system, I have no recourse to power it up other than 1) drive in
to work, or 2) get an HMC, correct?

I can remote from home to my work desktop, but since the System i is
powered off, there ain't not no Remote Control Panel.

Thanks.

--
Jeff Crosby
VP Information Systems
UniPro FoodService/Dilgard
P.O. Box 13369
Ft. Wayne, IN 46868-3369
260-422-7531
www.dilgardfoods.com

The opinions expressed are my own and not necessarily the opinion of
my company. Unless I say so.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L)
mailing

list

To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please
take a moment to review the archives at
http://archive.midrange.com/midrange-l.

--
Kirk
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take
a moment to review the archives at
http://archive.midrange.com/midrange-l.

--
Jeff Crosby
VP Information Systems
UniPro FoodService/Dilgard
P.O. Box 13369
Ft. Wayne, IN 46868-3369
260-422-7531
www.dilgardfoods.com

The opinions expressed are my own and not necessarily the opinion of my company. Unless I say so.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a moment to review the archives at http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.