RE: Socks server port

["Elvis Budimlic" <ebudimlic@xxxxxxxxxxxxxxxxxxxxxxxxx>]

iSeries client has the PORT keyword, FTP PORT(...).  So you can specify port
other than 21.  Also, even when inside the client and using OPEN, you can
specify the port again.
I don't know enough about your socks server to tell you if it'll allow for
that or not.  

Elvis

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Marc Rauzier
Sent: Wednesday, May 18, 2005 11:29 AM
To: Midrange Systems Technical Discussion
Subject: RE: Socks server port

Le mer. 18 mai 2005 14:44:02, Elvis Budimlic écrivait:

> NESTAT *CNN
> F14
> 
> will give you the port numbers.  
> 
> However, I am a bit confused about your setup.  Your socks server
> is running on the iSeries?  Then its port number should show in
> the WRKSRVTBLE and could be changed. No?
> 

Alas, no and this is the point. The socks server is *not* running on 
the iSeries. It is running somewhere on the intranet network to allow 
the FTP traffic from the iSeries to go out on the internet network. 

The FTP server on the internet server is listening on the classical 
port (21). But the iSeries when running the FTP client session, can 
only reach this FTP server by using the socks server that is listening 
on the 8090 port.

I have aleardy used this kind of setup (for a telnet session, but it is 
the same), and I know that when accessing to a server thru a socks 
server, the OS400 uses the standard socks server port which is 1080. 
So, my question is : is it possible to replace 1080 by 8090 and if yes, 
where can I do it ?

WRKSRVTBLE is used for servers that runs on the iSeries and even if it 
was not the case, I do not find any entry for any socks service.


> Elvis
> 
> -----Original Message-----
> From: midrange-l-bounces@xxxxxxxxxxxx
> [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Marc Rauzier
> Sent: Wednesday, May 18, 2005 1:38 AM
> To: Midrange Systems Technical Discussion
> Subject: RE: Socks server port
> 
> Le mar. 17 mai 2005 18:05:01, Wilt, Charles écrivait:
> 
>> WRKSRVTBLE ??
>> 
> 
> Thank you Charles.
> 
> Well, I was sure not to write down this question in a fine english
> :-) 
> 
> In my case, the AS400 is not the server, it is the client. It runs
> an FTP session to a FTP server thru a socks server (the socks
> server can only be configured with iSeries Navigator by
> right-clicking Properties on the TCP/IP configuration in the
> Network panel and filling the right informations in the SOCKS
> tab). The WRKSRVTBLE would help me if the AS400 have been FTP
> server which is not the case. 
> 
> 
>> Charles Wilt
>> iSeries Systems Administrator / Developer
>> Mitsubishi Electric Automotive America
>> ph: 513-573-4343
>> fax: 513-398-1121
>>  
>> 
>>> -----Original Message-----
>>> From: midrange-l-bounces@xxxxxxxxxxxx
>>> [mailto:midrange-l-bounces@xxxxxxxxxxxx]On Behalf Of Marc
>>> Rauzier Sent: Tuesday, May 17, 2005 11:31 AM
>>> To: midrange-l@xxxxxxxxxxxx
>>> Subject: Socks server port
>>> 
>>> 
>>> Hello everybody
>>> 
>>> When configuring the socks client on an AS400 for a socks 
>>> server (I want to 
>>> run FTP thru a socks server from the AS400), I do not see a 
>>> way to change 
>>> the port on which the socks server listens.
>>> 
>>> Does someone know if it is possible (changing from 1080 which 
>>> is, I guess, 
>>> the default and used value to, let's say 8090) and, if yes, how
>>> ? 
>>> 
>>> Note : OS400 V4R5
>>> 
> 
> 



-- 
Cordialement/Best regards
Marc Rauzier

Opinions I stated here are my own.

-- 
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.