RE: IPDS Inactivity Timer

[ChadB@xxxxxxxxxxxxxxxxxxxx]

Thanks!

We are already using a *PSFCFG on the printer devd... I just didn't think
to look there!

I can see the 'release timer' field there now and will give that a try.
Thanks!


                                                                           
             "Wilt, Charles"                                               
             <CWilt@xxxxxxxxxx                                             
             om>                                                        To 
             Sent by:                  "Midrange Systems Technical         
             midrange-l-bounce         Discussion"                         
             s@xxxxxxxxxxxx            <midrange-l@xxxxxxxxxxxx>           
                                                                        cc 
                                                                           
             05/03/2005 12:11                                      Subject 
             PM                        RE: IPDS Inactivity Timer           
                                                                           
                                                                           
             Please respond to                                             
             Midrange Systems                                              
                 Technical                                                 
                Discussion                                                 
             <midrange-l@midra                                             
                 nge.com>                                                  
                                                                           
                                                                           




You need to make use of a *PSFCFG object.

GO CMDPSFCFG.

On the device description, assign the PSF configuration you created above
via the USRDFNOBJ param.

*IPDS printers should normally always have a PSF config object assigned.

For more info:
http://www-912.ibm.com/s_dir/slkbase.NSF/643d2723f2907f0b8625661300765a2a/516c5f9756b1368a86256690004c3af3?OpenDocument&ExpandSection=6,5#_Section4


or

http://tinyurl.com/98lph


HTH,


Charles Wilt
iSeries Systems Administrator / Developer
Mitsubishi Electric Automotive America
ph: 513-573-4343
fax: 513-398-1121


> -----Original Message-----
> From: midrange-l-bounces@xxxxxxxxxxxx
> [mailto:midrange-l-bounces@xxxxxxxxxxxx]On Behalf Of
> ChadB@xxxxxxxxxxxxxxxxxxxx
> Sent: Tuesday, May 03, 2005 11:24 AM
> To: 'Midrange Systems Technical Discussion'
> Subject: IPDS Inactivity Timer
>
>
>
>
>
>
>
> We're getting used to some new IBM 1145 Multifunction printers that we
> recently installed and are noticing a delay after a job prints from an
> AS/400 outq.  For around 40 seconds after the job prints, the printer
> display shows 'busy network' and then goes back to ready
> status (and then
> is available for a copy/fax/network job).  In the interest of reducing
> contention for the printer,  i'm wanting to decrease the
> delay before the
> next job will kick in.
>
> I'm pretty sure the setting I need to adjust is the "inactivity timer"
> setting on the printer device description (i'd like to set it
> to *SEC15,
> which looks to be the minumum), but am not able to bring up
> this setting.
> The device is configured as *IPDS instead of a 3812.  Is this
> not something
> that can be adjusted when configured as *IPDS?
>
> Thanks for any possible advice from someone who knows!
>
> ______________________________________________________________
> _______________
> Scanned by IBM Email Security Management Services powered by
> MessageLabs. For more information please visit http://www.ers.ibm.com
> ______________________________________________________________
> _______________
> --
> This is the Midrange Systems Technical Discussion
> (MIDRANGE-L) mailing list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.
>
>

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.


_____________________________________________________________________________

Scanned by IBM Email Security Management Services powered by MessageLabs.
For more information please visit http://www.ers.ibm.com
_____________________________________________________________________________


ForwardSourceID:NT0001FCAA

_____________________________________________________________________________
Scanned by IBM Email Security Management Services powered by MessageLabs. For 
more information please visit http://www.ers.ibm.com
_____________________________________________________________________________