RE: Resetting internal modem without IPL

[pnelson@xxxxxxxxxx]

That wasn't it. IBM was helping me get a PPP connection configured, and 
the card wasn't playing nice. The purpose of the PPP connection was to 
facilitate 2-way batch transmissions with Palm Pilots. ECS was set up 
using their old external modem.


Paul Nelson
Arbor Solutions, Inc.
708-670-6978  Cell
pnelson@xxxxxxxxxx





"Ingvaldson, Scott" <SIngvaldson@xxxxxxxxxxxx>
Sent by: midrange-l-bounces@xxxxxxxxxxxx
09/09/2004 08:09 AM
Please respond to Midrange Systems Technical Discussion
 
        To:     "'midrange-l@xxxxxxxxxxxx'" <midrange-l@xxxxxxxxxxxx>
        cc: 
        Subject:        RE: Resetting internal modem without IPL


Are you thinking of QTIINSTL?

If you are trying to reset ECS you can use this.  Find controller
description QESCTL, QESPAP and QTICTL.  Vary of and delete these and all
devices under them.  Then vary off and delete QTILINE and QESLINE.  Then
CALL QTIINSTL.  This will rebuild everything that was just deleted.

If the problem is not ECS, check to make sure that something else is not
using the resource.  WRKHDWRSC *CMN and check all of the lines under the
resource (CMN01 ?) and make sure they are varied off first.  Then try to
vary on the line and controller.

If that doesn't work you can roll your own QTIINSTL by using RTVCFGSRC to
retrieve the source for your line, controllers and devices, then deleting
them and using this to rebuild them.

Regards, 
 
Scott Ingvaldson
iSeries System Administrator
GuideOne Insurance Group 

-----Original Message-----
date: Wed, 8 Sep 2004 12:53:26 -0500
from: pnelson@xxxxxxxxxx
subject: Re: Resetting internal modem without IPL

I assume you've tried the VRYCFG with a reset(*yes)? I recall that when I 
had problems with the card in the 820, the support line person had me run 
one of those "hidden" programs. It cleared up the problem for good. It 
must have flashed something down to the card's chip.


Paul Nelson
Arbor Solutions, Inc.
708-670-6978  Cell
pnelson@xxxxxxxxxx





Neil Palmer <NeilP@xxxxxxxxxxx>
Sent by: midrange-l-bounces@xxxxxxxxxxxx
09/08/2004 12:40 PM
Please respond to Midrange Systems Technical Discussion
 
        To:     Midrange Systems Technical Discussion 
<midrange-l@xxxxxxxxxxxx>
        cc: 
        Subject:        Resetting internal modem without IPL


Does anyone know if you can reset (maybe power off/on the card) the 
internal modems (2791/2793) in a model 270, 800, 810 etc. other than by 
IPL'ing the whole system ?
Maybe some method to do it through Service Tools in Hardware Service 
Manager ?

...Neil
--
 
This message and accompanying documents are covered by the Electronic
Communications Privacy Act, 18 U.S.C. §§ 2510-2521, and contains 
information
intended for the specified individual(s) only. This information is
confidential. If you are not the intended recipient or an agent 
responsible
for delivering it to the intended recipient, you are hereby notified that
you have received this document in error and that any review, 
dissemination,
copying, or the taking of any action based on the contents of this
information is strictly prohibited. If you have received this 
communication
in error, please notify us immediately by e-mail, and delete the original
message.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing 
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.