RE: Okidata w/jet direct -- MIDRANGE-L

> I did a little more checking.  The HP 500x and 300x series 
> both support IPP while the HP 170x series does not.

Bear with me, here's the latest:

I got an HP 500x print server and hooked it up.  Installed latest firmware.
Attached an Okidata ML380 to it.  I can install and print to it just fine
from my W2K machine.

This printer emulates an Epson 2550 by default.  I set up an iSeries
lan-attached device (not a remote outq) to test.  Made it *IBMIPPDRV for now
with manufacturer type/model *EPLQ2550.

When I send an iSeries print job it doesn't work.  I get:

POST / HTTP/1.1
Host: 192.168.0.103
Connection: close
Content-Type: application/ipp
Content-Length: 199
Accept: application/ipp
User-Agent: OS400

After that it slowly turns to garbage, then the printer writer ends.  The
joblog has:

CPD338D    Diagnostic              40   02/20/04  10:23:20.281600  QWPIPPDR
     QSYS        *STMT    QWPIPPDR    QSYS        *STMT
>From module . . . . . . . . :   WPIPPDR
>From procedure  . . . . . . :   Recv_Data
Statement . . . . . . . . . :   63
To module . . . . . . . . . :   WPIPPDR
To procedure  . . . . . . . :   _C_pep
Statement . . . . . . . . . :   *N
Message . . . . :   An error occurred while receiving data.
Cause . . . . . :   A communications error occurred while receiving data
from
remote device at RMTLOCNAME 192.168.0.103. The error code is 2329600. This
error can also occur when the system attempts to print to the remote device
after it has been powered off and on while the printer writer remains
active. Recovery  . . . :   Try the request again. If the problem continues,
end TCP/IP using the End TCP/IP (ENDTCP) command, start TCP/IP by using the
Start TCP/IP (STRTCP) command, and then try the request again.

Question: Do you feel confident that this is far enough along I will
eventually get it to work with a new Okidata 491?  I was only trying the
ML380 because I had it lying around.  It's really old and I have no clue as
to how that is affecting things.  There are so many options and settings to
printer setup on an iSeries that if this is going to be a time consuming
test and test and test, I'd just as leave do it with the OKI 491 that I
would ultimately use.

I just want to hear someone else say they feel confident that this would
ultimately work before I buy this printer.

Thanks.

-- 
Jeff Crosby
Dilgard Frozen Foods, Inc.
P.O. Box 13369
Ft. Wayne, IN 46868-3369
260-422-7531

The opinions expressed are my own and not necessarily the opinion of my
company.  Unless I say so.
 

> -----Original Message-----
> From: midrange-l-bounces@xxxxxxxxxxxx 
> [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jeff Crosby
> Sent: Thursday, February 19, 2004 8:28 AM
> To: 'Midrange Systems Technical Discussion'
> Subject: RE: Okidata w/jet direct
> 
> > > This used to be a 391 but it fried and was replaced by a 420. 
> > > Connected to a HP 500x
> 
> 
> The 500x supports up to 3 attached printers while the 300x supports 1.
> 
> --
> Jeff Crosby
> Dilgard Frozen Foods, Inc.
> P.O. Box 13369
> Ft. Wayne, IN 46868-3369
> 260-422-7531
> 
> The opinions expressed are my own and not necessarily the 
> opinion of my company.  Unless I say so.
> 
> 
> 
> _______________________________________________
> This is the Midrange Systems Technical Discussion 
> (MIDRANGE-L) mailing list To post a message email: 
> MIDRANGE-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change 
> list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, 
> please take a moment to review the archives at 
> http://archive.midrange.com/midrange-l.
> 
>