Re: Verify Alignment after changing controllers.

That's a good one :-) I use that too. I also have things setup to do a 
RTVCFGSRC every evening to a source
member named SCFGmmddyy (so today's would be SCFG071001)...

Chuck

MWalter@hanoverwire.com wrote:

> Chuck,
>
> No the device didn't re-create. I actually recreated the device when
> changing the controllers. I used the copy ,rename ,rename, delete method.
>
> Mark
>
> Mark Walter
> Sr. Programmer/Analyst
> Hanover Wire Cloth a div of CCX, Inc.
> mwalter@hanoverwire.com
> http://www.hanoverwire.com
> 717.637.3795 Ext.3040
>
>
>                     Chuck Lewis
>                     <clewis@iquest.net>        To:     MIDRANGE-L@midrange.com
>                     Sent by:                   cc:
>                     owner-midrange-l@mi        Subject:     Re: Verify 
>Alignment after changing controllers.
>                     drange.com
>
>
>                     07/10/01 03:44 PM
>                     Please respond to
>                     MIDRANGE-L
>
>
>
> ACTUALLY you get a G for Load Form Type and then an I for verify alignment.
> Normal procedure is to take a G and then an I.
>
> The device didn't recreate as something different than it was before did it
> ?
> Reason I ask is that if there was a Reply List Entry that looked for a
> specific
> printer and this changed, they would be seeing this when they hadn't
> before...
>
> Chuck
>
> Andy Nolen-Parkhouse wrote:
>
> > Mark,
> > I have to disagree with you here.  The "I" response basically says to
> ignore
> > the alignment and go ahead and print.  Thus it will prompt you for
> alignment
> > for the next spool file.  The "G" response says that you have aligned the
> > paper and to go ahead.  With a "G" it won't ask again until the spool
> writer
> > is ended and started again.
> > Regards,
> > Andy Nolen-Parkhouse
> >
> > Mark,
> >
> > Which option is being taken to the "Verify Alignment" message?  If you
> use
> > the "I" option, it will go away.  If "G" is used, it will do exactly what
> > you are seeing.
> >
> > Regards,
> >
> > Mike Shaw
> >
> > > Hello all,
> > >
> > > I've got a funky problem. We have a 5225 model 1 just recently moved
> from
> > a
> > > IBM 5494 using SNA to a Perle 594 controller using IP. The printer
> prints
> > > labels. Since the change over, the operator is getting a verify
> alignment
> > > message with every label. Does anyone know what might be causing this?
> > >
> > > Thank you,
> > >
> > > Mark
> > >
> > >
> > >
> > > Mark Walter
> > > Sr. Programmer/Analyst
> > > Hanover Wire Cloth a div of CCX, Inc.
> > > mwalter@hanoverwire.com
> > > http://www.hanoverwire.com
> > > 717.637.3795 Ext.3040
> > >
> > > +---
> > > | This is the Midrange System Mailing List!
> > > | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> > > | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> > > | To unsubscribe from this list send email to
> > MIDRANGE-L-UNSUB@midrange.com.
> > > | Questions should be directed to the list owner/operator:
> > david@midrange.com
> > > +---
> >
> > +---
> > | This is the Midrange System Mailing List!
> > | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> > | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> > | To unsubscribe from this list send email to
> MIDRANGE-L-UNSUB@midrange.com.
> > | Questions should be directed to the list owner/operator:
> > david@midrange.com
> > +---
> >
> > +---
> > | This is the Midrange System Mailing List!
> > | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> > | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> > | To unsubscribe from this list send email to
> MIDRANGE-L-UNSUB@midrange.com.
> > | Questions should be directed to the list owner/operator:
> david@midrange.com
> > +---
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
> MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
> david@midrange.com
> +---
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator: david@midrange.com
> +---

+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---