|
Chuck, I hope I've understood your question properly. Let me explain what I did in a very similar situation. Although not quite what you are asking for, I think it will give you a solution that avoids your DDM requirements. Since you've asked about creating DDM LF's within Harbinger, it sounds as if you are thinking of kicking off your process to load JDE PO's into Harbinger, from within Harbinger. I suggest you rethink this a bit, and kick it off from the system that produces your PO's. I had two AS/400's networked together. One had the PO application and it's files (although it wasn't JDE) , and the other was where our Harbinger application ran and EDI communications was done from. On the PO system, I wrote a CLP that would extract the PO's into a couple of files and then automatically SNADS the files to the EDI system. On the EDI system, I had a "message-handling" program always active that would look for the arrival of the SNADS message, and automatically receive them into a set of the same files on the EDI system. At this point, the Harbinger API was called to automatically load the PO's into Harbinger and send them via API. The whole thing was completely transparent and completely automated. I did use DDM in this application, but only from the PO system. I used DDM to "look into" Harbinger to see if the Vendor in question was setup to do EDI. If the Vendor was, the PO's were transmitted. If the Vendor was not, the PO's were printed on standard PO forms. I hope this helps. Feel free to email me privately if you'd like further details. Once this was set up it worked really well and was totally operator-proof. Bill "Graves, Chuck" <cgraves@roddapaint.com>@midrange.com on 04/18/2001 07:31:04 PM Please respond to MIDRANGE-L@midrange.com Sent by: owner-midrange-l@midrange.com To: <midrange-l@midrange.com> cc: Subject: EDI & DDM and JDEdwards I am trying to run Harbinger TrustedLink 400 on a model 170, and access files via DDM on a model 620 for outbound PO's from JDEdwards (F47116,F47117, etc), but i need to defind logicals within Harbinger and can't seem to do that with DDM files....has anyone been to this movie....can i get there from here? +--- | This is the Midrange System Mailing List! | To submit a new message, send your mail to MIDRANGE-L@midrange.com. | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com. | To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: david@midrange.com +--- -- NOTICE: The information contained in this electronic mail transmission is intended by Convergys Corporation for the use of the named individual or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone (collect), so that the sender's address records can be corrected. +--- | This is the Midrange System Mailing List! | To submit a new message, send your mail to MIDRANGE-L@midrange.com. | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com. | To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: david@midrange.com +---
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2025 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.