RE: New Machine, QSECOFR not authorized

["Joe Pluta" <joepluta@xxxxxxxxxxxxxxxxx>]

Wait a second here... there are eight slots on the brick... are those PORT
numbers?  And then I have to configure the TERMINAL to an address???

If so, how the heck do I configure the 3489?

(Shows how long it's been since I've done any twinax)

Joe

> -----Original Message-----
> From: owner-midrange-l@midrange.com
> [mailto:owner-midrange-l@midrange.com]On Behalf Of Neil Palmer
> Sent: Saturday, March 24, 2001 12:24 PM
> To: MIDRANGE-L@midrange.com
> Cc: Joe Pluta
> Subject: Re: New Machine, QSECOFR not authorized
>
>
> I would suspect the twinax screen isn't configured for addres 0.
>
> Neil Palmer      DPS Data Processing Services Canada Ltd.
> 50 Acadia Avenue, Ste.102                   AS/400~~~~~
> Markham, Ontario, Canada.   ____________          ___  ~
> Phone:(905) 474-4890 x303   |OOOOOOOOOO| ________  o|__||=
> Cell.:(416) 565-1682 x303   |__________|_|______|_|______)
> Fax:  (905) 474-4898         oo      oo   oo  oo   OOOo=o\
> mailto:NeilP@DPSlink.com  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> http://www.DPSlink.com     iSeries 400  The Ultimate Business Server
>
>
>
>
>
>
> "Joe Pluta" <joepluta@PlutaBrothers.com>
> Sent by: owner-midrange-l@midrange.com
> 2001/03/24 09:56
> Please respond to MIDRANGE-L
>
>
>         To:     <MIDRANGE-L@midrange.com>
>         cc:
>         Subject:        New Machine, QSECOFR not authorized
>
>
> I just plugged in a brand new machine, a model 270.  I connected the coax
> connector and the power plug, and turned the machine on.  I have a 3489
> Infowindow II attached to Port 0, and it comes up as "DSP01" in QBASE. So,
> I figure everything is cool.
>
> I log on as QSECOFR/QSECOFR, and I get CPF1110 Not Authorized to
> Workstation!  How can this be?  I tried QSYSOPR and QSECADM, neither of
> which would log on, and now I'm at the dreaded CPF1116 Next Unsuccessful
> Attempt Varies Off Device.
>
> I am in a quandary.  How do you initially make DSP01 available to sign on
> as
> QSECOFR?  There aren't a whole lot of manuals, but I do have the
> InfoCenter
> disks - is the information there?  Do I have to go through a special
> signon?
> (I seem to recall there was a special service signon - is that what I have
> to do?  And if so, how do I do it?)
>
> As a second question, what do you do if you DO manage to vary off DSP01?
> How do you get it back?
>
> Any help greatly appreciated.
>
> Joe
>
>
>
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
> MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
> david@midrange.com
> +---
>

+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---