RE: Overlay printing to Client Access printer

     Jim,
     
     In addition to MFRTYPMDL(*HP5SI), make sure you specify IMGCFG() as 
     appropriate for your printer (probably *IMGA02). I have not used 
     CAE to drive a printer, so I don't have actual experience with it. 
     I hope the IMGCFG parm helps.
     
     Eric


______________________________ Reply Separator
_________________________________
Subject: Re: Overlay printing to Client Access printer
Author:  "Jim Franz" <SMTP:franz400@triad.rr.com> at EXCHANGE
Date:    12/26/00 1:01 AM


I am also trying to print overlay to CA printer. 
Have a diff problem. CA printer configures
as AFP *NO. CHGDEVPRT will not allow 
change of that parm.
HPT is on. I have HP 1100 laser, and IBM 
recommends HP5si as closest fit. My CA 
only has up to HPIIIsi, which should still 
be AFP ok. Generated device as 3812-all 
looks ok except AFP=No.
Any help appreciated.
Jim
     
Booth - is your connection thru a remote controller?
A guess, but I beleive needs certain level on remote controllers 
for an advanced printer data stream. Same problem
with file transfers. Mostly non-IBM controllers.
     
----- Original Message -----
From: <booth@martinvt.com>
To: <MIDRANGE-L@midrange.com>
Sent: Tuesday, December 26, 2000 10:33 AM
Subject: Re: Overlay printing to Client Access printer
     
     
> Here's the error message I get:
>
>
>  Message ID . . . . . . :   CPA3388
>  Date sent  . . . . . . :   12/26/00      Time sent  . . . . . . : 
> 10:22:10
>
>  Message . . . . :   Attributes of file APN1099O not supported for device 
>
>    QPADEV0001.  (C G T H I)
>
>  Cause . . . . . :   Writer QPADEV0001 found attributes of file APN1099O 
> number
>    1 job 238861/BOOTH/QPADEV0004 on output queue QPADEV0001 in library 
> QUSRSYS
>    that are not supported for device QPADEV0001. The error code, or codes,

> are
>    2.  The error codes and their meaning are as follows: 
>      1 - Page size of file not supported on device.
>      2 - Device type of file not supported on device.
>      3 - Lines per inch (LPI) of file not supported on device. 
>
> The device is a HP IISI PC laser printer.  The printer session is
> configured automatically.  Both the device and the Client Access session 
> are set for Host Print Transform.  The WRKDEVD for QPADEV001 shows as a 
> 3812 printer.
>
> Any ideas?
>
>
>
> _______________________
> Booth Martin
> Booth@MartinVT.com
> http://www.MartinVT.com
> _______________________
>
>
>
>
> nina jones <ddi@datadesigninc.com>
> Sent by: owner-midrange-l@midrange.com 
> 12/24/2000 07:19 PM
> Please respond to MIDRANGE-L
>
>
>         To:     MIDRANGE-L@midrange.com 
>         cc:
>         Subject:        Re: Overlay printing to Client Access printer 
>
> >
> > Is there anything special about printing a form with an overlay to a PC 
> > laser printer attached to the AS/400 through a Client Access
> > auto-configured printer session?   The printer is an HPIII SI 
> > autoconfigured by the AS/400 to look like a 3812 printer
> >
>
> make sure host print transform is *yes and your printer type is set up. 
> nj
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com. 
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com. 
> | To unsubscribe from this list send email to 
MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator: 
david@midrange.com
> +---
>
     
+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com. 
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.

| Questions should be directed to the list owner/operator:
david@midrange.com 
+---
+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---