RE: TCP setup question

[Chris Bipes <chris.bipes@xxxxxxxxxxxxxxx>]

192.168.xxx.xxx is not an internet routable address.  You must get an
Internet Addressable address for your internet interface.  Or you must use
NAT to translate the 192.168.xxx.xxx to a routable address.  What IP address
was assigned to you from your ISP?  Do you have only one?  If so, you need
NAT!

Christopher K. Bipes    mailto:ChrisB@Cross-Check.com
Sr. Programmer/Analyst  mailto:Chris_Bipes@Yahoo.com
CrossCheck, Inc.        http://www.cross-check.com
6119 State Farm Drive   Phone: 707 586-0551 x 1102
Rohnert Park CA  94928  Fax: 707 586-1884

If consistency is the hobgoblin of little minds, only geniuses work here.
Karen Herbelin - Readers Digest 3/2000

-----Original Message-----
From: Mike Silvers [mailto:msilvers@hbs-inc.com]
Sent: Monday, November 13, 2000 6:57 AM
To: Midrange-L
Subject: TCP setup question


I have an interesting situation.  I have two Frame-Relay lines coming in.
One of the frame lines goes directly to a remote office in a different state
and the other frame line goes to the internet.  The IP scheme is as follows:

all internal traffic:  192.168.xxx.xxx
The internal network IP frame relay address:  192.168.100.21
The internet IP frame relay address:  192.168.106.21

I have created two interfaces:
192.168.100.254  255.255.255.0    ETHLINE1     *ELAN    (the company LAN)
192.168.106.254  255.255.255.0    ETHLINE1     *ELAN    (the internet)

 I have added the following routes:
*DFTROUTE        *NONE            192.168.106.21   *NONE    (the internet)
192.168.0.0      255.255.0.0      192.168.100.21   *NONE      (the company
LAN)

What I expected to occur was to have all internet traffic routed to the
internet port on the router and all other traffic routed to the company
frame relay.  This does not occur.  I can ping both router ports and I can
ping other LAN ports.  I can not ping any internet addresses.  We checked
the router and we can ping from the router to the internet.  I have added
the DNS servers (they are on the internet) and I can not reach them.  Both
interfaces are active and there are no port restrictions defined on the 400.

Does anyone have any ideas?

Thanks

Mike


================================

Mike Silvers, IBM Certified Expert
Hainey Business Systems
8 E. Canal St
Dover, PA 17315
Branch Office:  (410) 397-8739
Phone:  (800) 932-3380
Fax:  (717) 292-9474
Web: http:\\www.hbs-inc.com
________________________________
Providing E-Commerce, EDI, AS/400
Development and related services
nationwide.
================================

+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator:
david@midrange.com
+---
+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---