Re: SMTP taking 100% cpu utilization

[Ed Davidson <edavid3001@xxxxxxxxxxxx>]

Thank you for your reply, however this did not resolve my problem.  I did 
EXACTLY what you
specified, and my utilization was fine for a while, as it normally is after I 
reset SMTP, then
it skyrocketed back up.   Any other ideas?

Thank you,

Ed Davidson.



Tawbrey@ascend-tech.com wrote:

> Ed,
>
> You have a message stuck in the SMTP server. You will need to perform the
> following steps to clear the message and get things working again. This is
> due to IBM's wonderful implementation of SMTP on the AS/400. By the way you
> will lose any messages that have not already been processed. I would put
> this email in a safe place because we used to use the AS/400 for email and
> had this happen all the time, now we went to Domino on the AS/400's native
> SMTP and no problems at all.
>
> 1. ENDMSF
> 2. ENDTCPSVR *SMTP
> 3. CRTDTAARA DTAARA(QUSRSYS/QTMSCLEAN) TYPE(*CHAR) LEN(1) VALUE('c') AUT
> (*ALL)
> 4. STRMSF MSGOPT(*CLEAR)
> 5. STRTCPSVR *SMTP
>
> Thanks,
>
> Tony Awbrey
> Technical Specialist
>
> IBM Certified Specialist -- AS/400 Technical Solutions, Domino for AS/400
>
> Ascend Technologies, Inc.
> 2658 Crosspark Rd. Suite 200
> Coralville, IA 52241
> Voice: 319.626.5490 ext. 825
> Fax:     319.626.5491
>
>
>                     Ed Davidson
>                     <edavid3001@PRIMEIN        To:     MIDRANGE-L@midrange.com
>                     C.COM>                     cc:
>                     Sent by:                   Subject:     SMTP taking 100% 
>cpu utilization
>                     owner-midrange-l@mi
>                     drange.com
>
>
>                     04/11/2000 02:50 PM
>                     Please respond to
>                     MIDRANGE-L
>
>
>
> After it has been running for some time, the QTSMTPCLTP job will take as
> much of
> the processor as it can, making utilization 100% or ++++.
>
> I have V4R4, I have applied all of the group PTF's, all of the Group
> Hypers, and
> all of the Hypers as of April 10th, 2000.
>
> If I look at the job log of the job, it is almost empty.  No open files
> either.
>
> After an IPL, the system runs normal (20% utilization) for a few days or so
> before
> this starts up again.
>
>  This started after I closed off third party mail relay by configuring my
> AS/400 to
> send E-Mail through the firewall vs. relaying it to the firewall.  This
> didn't
> start immediately.
>
> Any ideas?
>
> Thank you;
>
> Ed Davidson.
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
> MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
> david@midrange.com
> +---
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator: david@midrange.com
> +---

+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---