|
Nimal: Have you recently upgraded form V4R3 to V4R4 and loaded a V4R3 version of QUSRSYS? This APAR was supplied to be from IBM, perhaps it will be helpful to you, it was to me. cjg |--------------+-----------------------------------------------------| | | | APAR#: II09973 | | | | | | | | Component: INFOAS400 - AS/400 Information | | | | | | | | Release(s) R370 | | | |--------------+-----------------------------------------------------| Abstract OSP-COMM-TCPIP-CFG-MSGTCP3CAC-F/QTMFCOM1-T/QTMFCOM1 Error Description If a pre-R370 version of library QUSRSYS is restored over the R370 version the Exit Point Programs required for FTP will be lost. The FTP Server Job, QTFTPxxxxx , will go Active but will end with ending code RC0. FTP Server Job's joblog will contain: msgTCP3CAC F/QTMFCOM1 T/QTMFCOM1 From module QTMFPUTL To module qtmf_ExitPgmIsRegistered Statement X/1204 To module QTMFPUTL To procedure qtmf_ExitPgmIsRegistered Statement X/1204 Exception CPF3CDB occurred when trying to get info for exit point QIBM_QTMF_SERVER_REQ with format name VLRQ0100 msgTCP3CAC is followed by msgTCP12F0 F/QTMFSRVR T/QTMFSRVR FTP Server intialization failed. . If a user issues a STRTCPSVR SERVER(*FTP) command the user joblog shows this command executing without error. Joblog contains msgCPC1221, job submitted and msgTCP1A0F , FTP server starting. . However, if the user issues a STRTCPFTP command the user joblog does contain the msgTCP3CAC with the same From and To programs/ modules/procedures as the msgTCP3CAC message in the FTP Server's joblog. . To reinstall the missing programs issue the following command: CALL QTCP/QTMFEXIT PARM('*INSTALL ') . Note: above command needs to be entered in uppercase and with the two trailing blanks after the . *INSTALL value. .** NOTE: User Profile needs to have *ALLOBJ Special Authority to issue the above command. . ADDITIONAL SEARCH WORDS: msgCPF3CDB TCP3CAC TCP 370 NOTE: QUSEXRGOBJ in QUSRSYS is the object that stores the exits shown with WRKREGINF Problem Summary Problem Conclusion Temporary Fix Comments cancel to prevent the APAR from remaining in INTRAN state Circumvention PTFs Available Affected Modules Affected Publications Summary Information Status................. CLOSED CAN Severity............... 4 HIPER.................. No PIN.................... Yes Reported Component..... INFOAS400 Fixed Component........ Failing Module......... Reported Release....... R370 Reported Release PTF... Latest Release PTF..... FESN................... 5NFO000 Duplicate Of........... IBM disclaims all warranties, whether express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. By furnishing this document, IBM grants no licenses to any related patents or copyrights. Copyright (c) 1994, 1995, 1996,1997,1998 IBM Corporation. Any trademarks and product or brand names referenced in this document are the property of their respective owners. Consult your product manuals for complete trademark information. Carl J. Galgano EDI Consulting Services, Inc. 540 Powder Springs Street, Suite C19 Marietta, GA 30064 (770) 422-2995 - voice (419) 730-8212 - fax mailto:cgalgano@ediconsulting.com http://www.ediconsulting.com AS400 EDI, Networking, E-Commerce and Communications Consulting and Implementation > -----Original Message----- > From: owner-midrange-l@midrange.com > [mailto:owner-midrange-l@midrange.com]On Behalf Of JDE Temp 1 > Sent: Wednesday, March 22, 2000 3:38 PM > To: MIDRANGE-L@midrange.com > Subject: FTP: Can not connect host > > > Hi, > > Does anyone know the reason for following messags when trying to > FTP. The PING with the same IP address gets through successfully. > > Cannot connect to host 10.1.1.1 at address 10.1.1.1. Try again later. > > Your help would be greatly appreciated. > > Nimal. > > +--- > | This is the Midrange System Mailing List! > | To submit a new message, send your mail to MIDRANGE-L@midrange.com. > | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com. > | To unsubscribe from this list send email to > MIDRANGE-L-UNSUB@midrange.com. > | Questions should be directed to the list owner/operator: > david@midrange.com > +--- +--- | This is the Midrange System Mailing List! | To submit a new message, send your mail to MIDRANGE-L@midrange.com. | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com. | To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: david@midrange.com +---
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.